SPECIFICATIONS

DIMENSIONS (HWD)

• Touch Panel: 4 3/4" x 7 9/16" x 13/16" (12.7 cm x 19.1 cm x 2.0 cm)
• Total Packaging Dimensions: 6 1/4" x 5 1/8" x 5" (14.2 cm x 6.5 cm x 4.1 cm)

WEIGHT

• Touch Panel: 1.4 lbs (604 g)
• Total Shipping Weight: 2.3 lbs (1.2 g)

POWER REQUIREMENTS (WITHOUT CHARGING)
Panel with battery fully charged or with no battery:

• Constant current draw: 0.3 A @ 12 VDC
• Startup current draw: 0.4 A @ 12 VDC

POWER REQUIREMENTS (WHILE CHARGING)
Panel while charging battery:

• Constant current draw: 1.1 A @ 12 VDC
• Startup current draw: 1.3 A @ 12 VDC

MINIMUM POWER SUPPLY REQUIRED
PS3.0 Power Supply (FG423-30): All MVP-5200i models are shipped with this power supply

POWER MODES

• On: All necessary modules are powered up and device remains online with the NetLinx Master.
• Sleep: Only the backlight will be turned off after the user selectable time of inactivity has elapsed. Panel resumes the ON mode in ~ 1 second.
• Shutdown: Power to all modules and components is turned off. The unit remains in this mode until either it is rebooted or the battery is completely shut down.

CERTIFICATIONS

• FCC Part 15 Class B and CE
• CE
• IEC60950
• RoHS
• Japan Approved
• Lithium-polymer microbattery: UN/IATA

BATTERY DURATION

• On mode – 6 hours of battery life
• Sleep mode – 8 hours of battery life

MEMORY

• 128 MB Mobile DDRAM (upgrade not available)
• 256 MB NAND FLASH (upgrade not available)

SCREEN PROPERTIES

• Size: 5.2" (13.21 cm)
• Screen resolution: 800 x 480 pixels (HV) @ 60 Hz frame frequency
• Type: WVGA
• Aspect ratio: 16 x 9
• Brightness (luminance): 300 cd/m²
• Channel transparency: 8-bit Alpha blending
• Contrast ratio: 400:1
• Display colors: 262,144 colors (18-bit color depth)
• Dot/pixel pitch: 0.23 mm
• Panel type: TFT Color Active-Matrix

VIEWING ANGLE

• Vertical: + 40° (up from center) and - 80° (down from center)
• Horizontal: + 60° (left from center) and - 60° (right from center)

EXTERNAL COMPONENTS

• Connector: 5-pin Mini-USB connector used for audio output to USB headphones, programming, firmware updates, and touch panel file transfer between the PC and the target panel.
  Note: When connecting the panel to PC using a CC-USB (or compatible) cable, be sure to power the panel On before attempting to connect the USB cable from the PC to the mini-USB port on the panel.
• DC Power Port: 2.5 mm port to power the panel away from a charging station
• Stylus Slot: Slot where the included stylus is stored, located on the right side of the device
• Microphone: For use with the intercom feature
• Frequency: 20 to 160,000 Hz
• S/N Ratio: More than 58 dB
• Speaker: 4 Ohm, 2 W 300 Hz cutoff frequency
• Audio Standards: G7.11 sound standard, 75 dB SPL@1m

INTERNAL COMPONENTS
IR Emitters: Transmit IR over 20 feet (6.10 m) from the panel.

• IR emitters on G4 panels share the device address number of the panel.
• Transmits AMX fixed frequencies at 38 kHz and 455 kHz and user programmable frequencies from 20 kHz to 1.5 MHz

ENVIRONMENTAL

• Operating Temperature: 0° C (32° F) to 40° C (104° F)
• Operating Humidity: 20% to 85% RH
• Storage Temperature: -20° C (-4° F) to 60° C (140° F)
• Storage Humidity: 5% to 85% RH

INCLUDED ACCESSORIES

• PS3.0 Power Supply (FG423-30)
• Stylus (pre-installed onto the left side of the unit)
• Integrated battery

Learn important installation, configuration and programming techniques in the following course(s) from AMX University:

• TPD4 Tutorial (Online)
• Getting Started with Intercom Enabled Touch Panels (Online)
• TPD4 UI Design
• Control Designer
• Quest for Power (Online)
• Control Installer

For schedules and registration for these and any AMX University courses, visit www.amx.com/training.

12.14.2009 - Important AMX MVP 5000 Series Battery Announcement