OVERVIEW
With the ability to integrate a large number of devices, the
NI-3100 controls a wide variety of components including
audio/video conferencing, projectors, VCR and DVD players,
projectors, lights, thermostats and other electronic equipment
found in larger areas. With these technology-driven environments,
the NI-3100 also provides solutions for future expansion and
enables the addition of more devices and control capabilities.
Offers higher performance with an ultra-fast processor, 64MB of
onboard RAM and is AMX Device Discovery enabled.
COMMON APPLICATION
The NI-3100 unit is ideally suited to the requirements of larger
areas or multiple rooms with advanced control and
automation features.
FEATURES
- 7 Configurable RS-232 / RS-422 / RS-485 Serial ports
- 8 Relays
- 8 IR / Serial ports
- 8 Digital I/O ports
- 2 Communication Networks: AxLink and Ethernet (TCP/IP)
- 404 MIPS processor speed
- 64 MB RAM
- 256 MB CompactFlash (upgradeable to 1 G)
- 1 MB Non-Volatile Memory
- AMX Device Discovery enabled
SPECIFICATIONS
DIMENSIONS (HWD)
- 3 1/2” x 17” x 3 1/2” (8.8 cm x 43.2 cm x 8.8 cm)
- RU: 2
WEIGHT
4.55 lbs (2.06 kg)
POWER
900 mA @ 12 VDC
ENCLOSURE
Metal with black matte finish
MEMORY
- 64 MB SDRAM
- 1 MB of Non-volatile SRAM
COMPACT FLASH
128 MB Card or more (upgradeable)
ONBOARD MASTER
404 MIPS
CERTIFICATIONS
FCC Part 15 Class B, CE, and IEC 60950
FRONT PANEL COMPONENTS
- LINK/ACT
- Status: Green LED blinks to indicate that the system is programmed and communicating properly
- Output: Red LED blinks when the Controller transmits data, sets channels and sends data strings, etc.
- Input: Yellow LED blinks when the Controller receives data from button pushes, strings, commands, channel levels, etc.
- RS-232/422/485 LEDs
- Relay LEDs
- IR/Serial LEDs
- I/O LEDs
- Rack-mount brackets: Provides an installation option for the Integrated Controller to be mounted into an equipment rack, when used with the Installation Kit (KA2105-01)
REAR PANEL CONNECTORS
- RS-232/422/485 (Ports 1 - 7)
- ICSNet: Two RJ-45 connectors for ICSNet interface (provided by ICSNet daughter card)
- ICSHub Out: RJ-45 connector provides data to a Hub connected to the Controller (provided by ICSNet daughter card)
- Relay (Port 8)
- Digital I/O (Port 17)
- IR/Serial (Ports 9-16)
- Program Port
- Configuration DIP Switch: Sets the communication parameters for the Program port
- ID Pushbutton
- Ethernet Port: RJ-45 port for 10/100 Mbps communication. LEDs show communication activity, connection status, speeds, and mode information: - SPD (speed) - Yellow LED lights On when the connection speed is 100 Mbps and turns Off when the speed is 10 Mbps. - L/A (link/activity) - Green LED lights On when the Ethernet cables are connected and terminated correctly, and blinks when receiving Ethernet data packets.
- AxLink LED
- AxLink Port: 4-pin 3.5 mm mini-Phoenix (male) connector that provides data and power to external control devices
- Power Port: 2-pin 3.5 mm mini-Phoenix (male) connector
ENVIRONMENTAL
Heat Dissipation (Typical): 36.9 BTU/hr
INCLUDED ACCESSORIES
- 2-pin 3.5 mm mini-Phoenix (female) PWR connector (41-5025)
- 4-pin 3.5 mm mini-Phoenix (female) AxLink connector (41-5047)
- 10-pin 3.5 mm mini-Phoenix (female) I/O connector (41-5107)
- Two 8-pin 3.5 mm mini-Phoenix female Relay connectors (41-5083)
- Two CC-NIRC IR Emitters
- Two removable rack ears (62-2105-07)
Learn important installation, configuration and programming techniques in the following course(s) from AMX University:
- AMX Essentials (Online)
- Getting Started with AMX (Online)
- Control Designer
- Quest for Power (Online)
- Control Installer
- Control Programmer 1
- Getting Started with AMX Modules (Online)
- Control Programmer 2
- Control Programmer 3
- Introduction to Duet (Online)
- Building Java Modules using Café Duet
For schedules and registration for these and any AMX University courses, visit www.amx.com/training.
TRAINING AVAILABLE
Learn important installation, configuration and programming techniques in the following course(s) from AMX University:
- AMX Essentials (Online)
- Getting Started with AMX (Online)
- Control Designer
- Quest for Power (Online)
- Control Installer
- Control Programmer 1
- Getting Started with AMX Modules (Online)
- Control Programmer 2
- Control Programmer 3
- Introduction to Duet (Online)
- Building Java Modules using Café Duet
For schedules and registration for these and any AMX University courses, visit www.amx.com/training.
GSA
This product has been approved by the U.S. Government’s General Services Administration to be specified for use in government installations.