SPECIFICATIONS

DIMENSIONS (HWD)

• 2" x 17" x 10" (5.1 cm x 43.2 cm x 25.4 cm)
• RU: 1

WEIGHT
6.95 lbs (3.15 kg)

POWER
900 mA @ 12 VDC

ENCLOSURE
Metal with black matte finish and translucent polycarbonate faceplate

ONBOARD MASTER
Processing Power: 32-bit microprocessor, 404 MIPS, Real-time operating system
Memory: Volatile – 64 MB, Non-Volatile – 1 MB, Flash – 256 MB or more
Networking:

• AxLink – 4-wire network (20.8 kbps) connects up to 255 Axcess devices, operates up to 3,000 feet of wiring and supplies 12 VDC power
• Ethernet – Direct 10/100 BaseT Ethernet networking Ethernet Protocols used by NI-3101-SIG
• ICSP – peer to peer protocol used for both master-to-master and master-to-device communications
• ICMP – To connect over a network, ping a NI-3101-SIG
• Telnet – NetLinx telnet server provides a mechanism to configure and diagnose a NetLinx system
• HTTP – NI-3101-SIG has a built-in web server that complies with the HTTP 1.0 specification and supports all of the required features of HTTP v1.1
• FTP – NI-3101-SIG has a built-in FTP server that conforms to RFC
• integration! Solutions – uses port 10500 for XML based communication protocol

CONTROL PORTS

• Six Serial data control ports (RS-232/422/485), with XON/XOFF and CTS/RTS, 300-115,200 baud
• Eight IR/Serial ports for control of up to 1.142 MHz carrier frequency
• Eight I/O channels for contact closure, 0-5 VDC voltage sensing, or interactive power sensing for IR ports
• Eight Relays - single-pole single-throw relay ports, independently controlled

FRONT PANEL COMPONENTS

LED INDICATORS

• LNK/ACT: Blue LED lights when the Ethernet cables are connected and terminated correctly and blinks when receiving Ethernet data packets
• Status: Blue LED blinks to indicate that the system is programmed and communicating properly
• Output: Blue LED blinks when the Master transmits data, sets channels on and off, sends data strings, etc.
• Input: White LED blinks when the Master receives data from button pushes, strings, commands, channel levels, etc.

RS-232/422/485 LEDs

• Six sets of blue and white LEDs light to indicate Ports 1-6 are transmitting or receiving RS-232, 422, or 485 data
• TX LEDs (blue) blink when transmitting data
• RX LEDs (white) blink when receiving data

RELAY LEDs
Eight blue LEDs light to indicate relay channels 1-8 are active (closed) on Port 8

IR/SERIAL LEDs
Eight blue LEDs light to indicate the IR/Serial ports 9-16 are transmitting control data

I/O LEDs
Eight white LEDs light when the I/O channels 1-8 are active on Port 17

REAR PANEL CONNECTORS

POWER CONNECTOR
2-pin (male) green captive-wire connector for 12 VDC power supply

ETHERNET 10/100 PORT
RJ-45 Ethernet 10/100 connector. Automatically negotiates connection speed and whether to use half or full duplex mode

AXLINK CONNECTOR
Black 4-pin (male) captive-wire connector that provides data and power to external control devices (6 A max power rating)

PROGRAM PORT
USB connector that supports USB communications to a PC for system programming and diagnostics

CONFIGURATION DIP SWITCH
4-position DIP switch

ID BUTTON
Pushbutton sets device address ID (in conjunction with NetLinx Studio v1.2 build 200 or higher software program)

RS-232/422/485 (PORTS 1-6)
Six RS-232/422/485 control ports using DB-9 (male) connectors with XON/XOFF (transmit on/transmit off), CTS/ RTS (clear to send/ready to send), and 300-115,200 baud

RELAYS (PORT 8)

• 8-channel single-pole single throw relay ports
• Each relay is independently controlled
• Supports up to 8 independent external relay devices
• Each relay can switch up to 24 VDC or 28 VAC @ 1 A
• Two 8-pin mini-Phoenix connectors (3.5 mm) provide relay termination

DIGITAL I/O (PORT 17)

• 8-channel binary I/O port for contact closure
• Each input is capable of 0-5 VDC voltage sensing. Input format is software selectable
• One 10-pin mini-Phoenix connector (3.5 mm) provide I/O port termination

IR/SERIAL (PORTS 9-16)

• Eight IR/Serial control ports support high-frequency carriers up to 1.142 MHz
• Each output is capable of two electrical formats: IR or Serial
• Eight IR/Serial data signals can be generated simultaneously
• Two 8-pin mini-Phoenix connectors (3.5 mm) provide IR/ Serial port termination

ENVIRONMENTAL

• Operating Temperature: 0° C (32° F) to 50° C (122° F)
• Operating Humidity: 20% to 85% RH
• Heat Dissipation (Typical): 36.9 BTU/hr

INCLUDED ACCESSORIES

• Removable rack ears allow for tabletop, under-counter, and front/rear rack mounting
• Removable feet give a finished look and provide spacing between stacked components
• Two 8-pin mini-Phoenix female connectors (41-5083)
• One 10-pin mini-Phoenix female connector (41-5107)
• Two CC-NIRC IR Emitters (FG10-000-11)
• One 4-pin 3.5 mm mini-Phoenix AxLink connector (41-5047)
• One 2-pin mini-Phoenix PWR connector (41-5025)
• One Relay Terminal Common Strip (41-2105-01)
• Four Rack mount screws (80-0186)
• Four washers (80-0342)

Learn important installation, configuration and programming techniques in the following course(s) from AMX University:

• AMX Essentials (Online)
• Getting Started with AMX (Online)
• Control Designer
• Quest for Power (Online)
• Control Installer
• Control Programmer 1
• Getting Started with AMX Modules (Online)
• Control Programmer 2
• Control Programmer 3
• Introduction to Duet (Online)
• Building Java Modules using Café Duet

For schedules and registration for these and any AMX University courses, visit www.amx.com/training.