SPECIFICATIONS

DIMENSIONS (HWD):

• (With faceplate): 4.15" x 5.59" x 1.97" (10.50 cm x 14.20 cm x 5 cm)

WEIGHT

• 12.8 oz (360 grams)

POWER REQUIREMENTS (Without Charging)

• PoE Powered - No local Power Supply needed
• Max power draw: 5.5 W

PANEL LCD PARAMETERS

• Aspect ratio: 16 x 9
• Maximum brightness (luminance): 200 cd/m2
• Channel transparency: 8-bit Alpha blending
• Contrast ratio: 250:1
• Display colors: 256 thousand colors (18-bit color depth)
• Dot/pixel pitch: 0.14 mm
• Panel type: TFT Color Active-Matrix
• Screen resolution: 800 x 480 pixels (HV) @ 60 Hz frame frequency
• Viewing dimensions: 4.3" x 2.58" (109.2 mm x 65.2 mm)

VIEWING ANGLE

• Up/Down/Left/Right: 45/65/60/60

IR RECEPTION ANGLE

• Horizontal: + 25° (left and right from center)
• Vertical: + 15° (up and down from center)

FRONT PANEL COMPONENTS

• Light Sensor: Photosensitive light detector for automatic adjustment of the panel brightness
• Motion Sensor (PIR): Proximity Infrared Detector to wake the panel when panel is approached
• Front Bezel Button: Provides both access to the Setup and Calibration pages and toggles the panel between a "sleep" or "wake" state. This button is also user-programmable
• Microphone: Frequency response of 300 to 3400Hz; used for intercom applications
• Speaker: Output of 4Ohm, 2 Watts, with a 300Hz low cutoff frequency

SUPPORTED AUDIO SAMPLE RATES
48000Hz, 44100Hz, 32000Hz, 24000Hz, 22050Hz, 16000Hz, 12000Hz, 11025Hz, and 8000Hz

INTERCOM
Full duplex VoIP capabilities

SIDE PANEL CONNECTORS

• Ethernet 10/100 Port: RJ-45 port for 10/100 Mbps communication. The Ethernet port automatically negotiates the connection speed (10 Mbps or 100 Mbps), and whether to use half duplex or full duplex mode. Power is supplied through Power Over Internet (PoE). NXD-500i panels communicate with the NetLinx Master using the ICSP protocol over Ethernet. LEDs show communication activity, connections, speeds, and mode information:
• L/A-link/activity - Yellow LED lights On when the Ethernet cables are connected and terminated correctly and then blinks when receiving Ethernet data packets
• SPD-speed - Green LED lights On when the connection speed is 100 Mbps and turns Off when the speed is 10 Mbps
• Mini-USB Connector: 5-pin Mini-USB connector used for programming, firmware update, and touch panel file transfer between the PC and the target panel. The connector is also used for providing audio output for external speakers

MEMORY (FACTORY DEFAULT)

• 128 MB SDRAM
• 256 MB integrated Flash Memory (not upgradeable - factory programmed)

CERTIFICATIONS

• FCC Part 15 Class B, CE, IEC 60950, RoHS

OPERATING / STORAGE ENVIRONMENTS

• Operating Temperature: 0° C (32° F) to 40° C (104° F)
• Operating Humidity: 5% - 85% RH
• Storage Temperature: -20° C (-4° F) to 60° C (140° F)
• Storage Humidity: 5% - 85% RH

BTU/HR

• 18.8

INCLUDED ACESSORIES

• Front Bezel (60-2261-11)

Learn important installation, configuration and programming techniques in the following course(s) from AMX University:

• TPD4 Tutorial (Online)
• Getting Started with Intercom Enabled Touch Panels (Online)
• TPD4 UI Design
• Control Designer
• Quest for Power (Online)
• Control Installer

For schedules and registration for these and any AMX University courses, visit www.amx.com/training.