NXR-ZRP NetLinx® ZigBee Repeater

OVERVIEW
The NetLinx ZigBee Repeater can be added throughout the installation to ensure a comprehensive, broad wireless coverage area with no "dead spots," or where extra coverage is needed.

COMMON APPLICATION
Ideal for increasing the wireless coverage area of ZigBee devices throughout residences or commercial buildings.

FEATURES

  • Can coexist with 802.11 wireless networks without signal interference
  • Supports 16 wireless channels for interference tolerance
  • Provides redundant paths of communication
  • Configurable to include or exclude a ZigBee device on the ZigBee network

SPECIFICATIONS

DIMENSIONS (HWD)
1” x 2 1/2” x 3 1/2” (2.3 cm x 6.4 cm x 8.7 cm)
Note: depth does not include antenna

WEIGHT
4 oz (113.39 g)

POWER
10.5 - 18 VDC; (13.5 VDC nominal operation voltage)

MEMORY

  • 16 MB of FLASH
  • 1 MB external memory

RADIO SPECIFICATIONS

  • Frequency: 2.4 GHz
  • Operating Channels: 11 – 26
  • Modulation Technique: DSS
  • Output Power: Region/country specific
  • Coverage Area: 165 feet (50.2 m)

FIRMWARE/SOFTWARE SPECIFICATIONS

  • IP Configuration: Static IP or DHCP client (default is static, 192.168.1.140)
  • Communications: ZigBee, TCP/IP, The NXR-ZRP communicates with a NetLinx master via a NXR-ZGW.

FRONT COMPONENTS

  • LEDs
    • PWR/STATUS: Power ON is indicated with a solid light. Power OFF is indicated with no light.
    • RF: The LED is solid when end devices are connected; end devices not connected is indicated with no LED light; the LED blinks to indicate activity.
    • ICSP: The LED is solid when ICSP connection is in place with the NetLinx master.
  • Antenna Mount: A reverse SMA connection that supports a 2.4GHz antenna.
  • ID Button: Press and hold for approximately 10 seconds to return the NXR-ZRP to factory default settings.

REAR COMPONENTS

  • Power connector : 2-pin 3.5mm captive-wire connector

ENVIRONMENTAL

  • Operating Temperature: -30ºC (-22ºF) to 70ºC (158ºF)
  • Relative Humidity: 5% to 85% non-condensing; intended for indoor use only)

CERTIFICATIONS
IC ID: 5088A-ZRD, CE, IEC 60590, TELEC

INCLUDED ACCESSORIES

  • Rubber feet
  • Velcro mounting strip
  • 2.4GHZ, MONO, RSMA, 3.5IN, 2.0DBI Antenna (70-0012-SA)
  • Power Supply (24-5791-SA)
NXR-ZRP /assets/diagrams/NXR-ZGW.ZRP.Diagram.pdf /imgs/diagrams/NXR-ZGW.ZRP.Diagram.png _blank PDF | 856 KB

Learn important installation, configuration and programming techniques in the following course(s) from AMX University:

  • Getting Started with Wireless Technology (Online)

For schedules and registration for this and any AMX University course, visit www.amx.com/training.
/assets/coolIcons/amxUniversity.png

TRAINING AVAILABLE
Learn important installation, configuration and programming techniques in the following course(s) from AMX University:

  • Getting Started with Wireless Technology (Online)

For schedules and registration for these and any AMX University courses, visit www.amx.com/training.

 MX NXR-ZRP Products default.asp User Interface Accessories categoryUserInterfaceAccessories.asp NXR-ZRP NXR-ZRP.asp FG5791-02 NetLinx ZigBee Repeater
2007-07-05 User Interface Acc. ZigBee White Paper /assets/whitePapers/AMX.ZigBee.White.Paper.pdf PDF | 88.0 KB _blank NXR-ZGW NXR-ZRP NXR-ZGW-PRO NXR-ZRP-PRO 2007-07-05 User Interface Acc. Wireless Site Survey Guide /assets/whitePapers/AMX.Wireless.Site.Survey.Guide.pdf PDF | 308 KB _blank NXA-WAP250G NXR-ZGW NXR-ZRP NXR-ZGW-PRO NXR-ZRP-PRO 2009-10-01 Network/Comm. NXR-ZGW NetLinx ZigBee Pro Repeater Firmware 3.01.05 /assets/firmwareFiles/SW5791_07_ZIGBEE_REPEATER_v3_01_05.kit _self KIT | 104 KB

NEW LOADING PROCEDURE for v3.01.07:

  1. This upgrade will require two loads of the file SW5791_01A_NXR_ZGW_v3_01_07.kit. The first load will fail after the third file is transferred with the NetLinx error message "Transfer Aborted- Unsupported file type." After getting this error message, reboot the gateway and verify that the NetLinx OnLine Tree shows v3.01.07 for the version on the gateway. Transfer file SW5791_01A_NXR_ZGW_v3_01_07.kit to the gateway a second time with the "Reboot Device" box checked in NetLinx. This time the entire kit file will transfer. After the gateway reboots, it will download the firmware to the radio. This will take approximately two minutes.
  2. Load SW5795_92_ZIGBEE_END_DEVICE_v3_01_05.kit - a gateway reboot IS NOT necessary after sending this file.
  3. Load SW5791_07_ZIGBEE_REPEATER_v3_01_05.kit - a gateway reboot IS NOT necessary after sending this file.

New Features:

  • The radio builds have been broken out of the gateway kit file. Each radio has a separate kit file that must be loaded onto the gateway - SW5795_92_ZIGBEE_END_DEVICE_vX_XX_XX.kit and SW5791_07_ZIGBEE_REPEATER_vX_XX_XX.kit. This was done so that changes made to any one of the radio builds may be loaded onto the gateway without rebuilding the gateway kit file. The file SW5795_92_ZIGBEE_END_DEVICE_vX_XX_XX.kit contains the radio firmware for over the air upgrades for the R3 and R4. The file SW5791_07_ZIGBEE_REPEATER_vX_XX_XX.kit contains the radio firmware for over the air upgrades for the NXR-ZRP-PRO Repeater.

CHANGES in this Release:

  • Resolved bugs with connectivity (R4/R3s falling offline and never coming back online)
  • Added support for the "DEVICE_WAKE" NetLinx command
  • Resolved several minor gateway web page bugs
  • Added support for the Get Time function

Known Issues:

  • On systems that have one gateway and no repeaters, the gateway or remotes can become inoperable under extreme amounts of traffic (for example, 30 messages every two seconds to each of six remotes). Rebooting these devices will bring them back online.
  • Setting the gateway device number to 0 can cause it to not be correctly recognized by the master.
  • The gateway does not currently support NDP mode for master connections.
  • In high traffic situations remotes can appear on the gateway commissioning page, even though they are commissioned. This has no impact on the actual operation of the remotes.
  • In some cases, the R3 power source will show as "Unknown" on the gateway web pages when the R3 is in its cradle. This issue does not impact the functionality of the remote or the gateway.

 2009-10-01 NXR-ZGW NXR-ZGW-PRO NXR-ZRP NXR-ZRP-PRO en au AMX Products R-4 and The Mio Modero Remote Family 2008-09-04 window.open('/flash/literature/R4.Brochure/index.html','literatureWindow','top=20,left=20,resizable=1');return false; /assets/literature/R4.Mio.Modero.Remote.Family.pdf /assets/literature/thumbs/amx_R4MioModeroRemoteFamily.jpg _blank PDF | 6.20 MB MIO R-1 MIO R-2 MIO R-3 MIO R-4 MIO-RCC-KIT NXR-ZGW NXR-ZRP 1 en au 1 300 1 no no 97-1000 de eu AMX Products R-4 and The Mio Modero Remote Family 2008-09-04 window.open('/flash/literature/R4.Brochure/index.html','literatureWindow','top=20,left=20,resizable=1');return false; /assets/literature/R4.Mio.Modero.Remote.Family.pdf /assets/literature/thumbs/amx_R4MioModeroRemoteFamily.jpg _blank PDF | 6.20 MB MIO R-1 MIO R-2 MIO R-3 MIO R-4 MIO-RCC-KIT NXR-ZGW NXR-ZRP 1 de eu 1 300 1 no yes 97-1000 User Interface Acc. NXR-ZRP - Front /assets/logosAndPhotos/NXR-ZRP-Front.png /assets/logosAndPhotos/thumbnails/NXR-ZRP-Front.jpg _blank PNG | 548 KB NXR-ZRP 1 User Interface Acc. NXR-ZRP - Rear /assets/logosAndPhotos/NXR-ZRP-Rear.png /assets/logosAndPhotos/thumbnails/NXR-ZRP-Rear.jpg _blank PNG | 556 KB NXR-ZRP 1 2010-04-09 Network/Comm. Operation/Reference Guide - NXR-ZGW/NXR-ZRP NetLinx ZigBee Gateway and Repeater /techdocs/NXR-ZGW.ZRP.OperationReferenceGuide.pdf _blank 2010-04-09 PDF | 3.13 MB NXR-ZGW NXR-ZRP 2009-07-06 Network/Comm. Installation Guide - NXR-ZGW/NXR-ZRP NetLinx ZigBee Gateway and Repeater /techdocs/NXR-ZGW.ZRP.InstallationGuide.pdf _blank 2009-07-06 REV G PDF | 180 KB NXR-ZGW NXR-ZRP NXA-WAP2405A NXA-WAP2413A NXA-WAP2410A NXA-WAP2403A 2007-10-09 Network/Comm. Installation Guide - ZigBee Installation Tips /techdocs/ZigBee.InstallationGuide.pdf _blank 2007-10-09 REV A PDF | 212 KB MIO-R3 MIO-R4 NXR-ZGW-PRO NXR-ZRP-PRO NXR-ZGW NXR-ZRP 2006-09-25 Remote Controls ZigBee Gateway Presentation /assets/presentations/AMXZigBeeGatewayPres.pps PPS | 1.84 MB _blank NXR-ZGW NXR-ZRP