SPECIFICATIONS

DIMENSIONS (HWD)

• Fully raised: 6.86" x 7.96" x 6.93" (17.40 cm x 20.20 cm x 17.60 cm)
• Fully lowered height: 3.70" (9.40 cm)

WEIGHT
2.5 lb (1.12 kg)

POWER REQUIREMENTS

• PoE Powered - No local Power Supply needed
• Max power draw: 5.5W

MEMORY

• 128 MB SDRAM
• 256 MB integrated Flash Memory (not upgradeable - factory programmed)

PANEL LCD PARAMETERS

• Aspect Ratio: 16:9
• Brightness: 300 cd/m2
• Contrast ratio: 400:1
• Display colors: 256K colors (18-bit color depth)
• Dot/pixel pitch: 0.19 mm
• Panel type: TFT Color Active-Matrix
• Screen Resolution: 800 x 480 pixels (HV) @ 60 Hz frame frequency

ACTIVE SCREEN AREA
6.00" x 3.60" (15.24 cm x 9.14 cm)

VIEWING ANGLE
Up/Down/Left/Right: 70/60/70/70

IR RECEPTION ANGLE

• Horizontal: ± 50° (left and right from center)
• Vertical: ± 30° (up and down from center)

SUPPORTED AUDIO SAMPLE RATES
48000Hz, 44100Hz, 32000Hz, 24000Hz, 22050Hz, 16000Hz, 12000Hz, 11025Hz, and 8000Hz

FRONT PANEL COMPONENTS

• Light Sensor: Photosensitive light detector for automatic adjustment of the panel brightness
• Motion Sensor (PIR): Proximity Infrared Detector to wake the panel when panel is approached
• Front Bezel Button: Provides both access to the Setup and Calibration pages and toggles the panel between a "sleep" or "wake" state. This button is also userprogrammable.
• Speaker: Output of 4 Ohm, 2 Watts, and 300Hz low cutoff frequency

REAR CONNECTORS

• Ethernet 10/100 Port: RJ-45 port for 10/100 Mbps communication. The Ethernet port automatically negotiates the connection speed (10 Mbps or 100 Mbps), and whether to use half duplex or full duplex mode. Power is supplied through Power Over Ethernet (PoE). CA7 panels communicate with the NetLinx Master using the ICSP protocol over Ethernet. LEDs show communication activity, connections, speeds, and mode information:
• L/A-link /activity - Yellow LED lights On when Ethernet cables are connected and terminated correctly and then blinks when receiving Ethernet data packets.
• SPD-speed - Green LED lights On when the connection is 100 Mbps and turns off when the speed is 10 Mbps.
• Mini-USB Connector: 5-pin Mini-USB connector used for programming, firmware update, and touch panel file transfer between the PC and the target panel. The connector is also used for providing audio output for external speakers.

CERTIFICATIONS

• FCC Part 15 Class B and CE
• IEC 60950
• RoHS

ENVIRONMENTAL

• Temperature Operating: 0° C (32° F) to 40° C (104° F)
• Operating Humidity: 20% to 85% RH
• Temperature Storage : -20° C (-4° F) to 60° C (140° F)
• Storage Humidity: 5% to 85% RH

OTHER AMX EQUIPMENT

• PS-POE-AF PoE Injector (FG423-80)
• CC-USB Type-A to Mini-B5-wire programming cable (FG10-5965)
• USB to Headphone Adaptor (FG5966-23)
• NXA-ENET8-2POE, Gigabit PoE Ethernet Switch (FG2178-63)

Learn important installation, configuration and programming techniques in the following course(s) from AMX University:

• TPD4 Tutorial (Online)
• TPD4 UI Design
• Control Designer
• Quest for Power (Online)
• Control Installer

For schedules and registration for these and any AMX University courses, visit www.amx.com/training.