UPC20+

Universal Power/Motor Controller, 20 A (110/220 VAC input)

DescriptionUniversal Power/Motor Controller
Part #FG672

HELPFUL HINT
If UPC20+ is powered up when changes are made to Dip Switch settings, then power must be cycled before changes can take effect.

COUNTRY OF ORIGIN: UNITED STATES

To satisfy the requirements/regulations of existing or future government programs, this two-letter code is being provided to designate the country of origin for this product.

(Click here for a list of all countries and their respective two-letter code.)

OVERVIEW
Designed for conduit installation, the Universal Power/Motor Controller, 20 A (110/220 VAC input) is a dual 20-amp AC power and motor controller. Configure a wide range of power and motor control modes for a full range of devices ranging from simple wall panels with low voltage contact closure to large systems requiring high voltage contact closure.

The UPC20+ supports two primary operating modes. In Motor Control Mode, the two relays are automatically activated in sequence with an adjustable delay from 0 to 90 seconds. In this mode, there are three control options:

  • Single Button Mode operates with one pushbutton in a sequence: Up, Stop, Down, Stop and so on for each successive button press.
  • Two/Three Button Mode operates with two pushbuttons, one for Up and one for Down and optionally one for stop.
  • Momentary On/Off operates the first relay only while the button is pressed and then second the relay activates when the button is released.

In Power Control mode, the UPC20+ provides power control for two independent circuits with a combined total load of 20 Amps. In this mode, there are three control options:

  • Momentary Power Mode operates the selected relay only while the button is pressed. The relay is de-activated when the button is released.
  • Latching Power Mode toggles between activating and deactivating the selected relay on each successive button press.
  • Two Button On/Off Mode uses two buttons for each relay, one to activate and one to deactivate.

FEATURES

  • 1, 2 and 3-button logic modes
  • Local test switches with status LEDs
  • 120, 240, and 277 VAC control capability
  • ETL listed

SPECIFICATIONS

DIMENSIONS (HWD)

  • 8 1/2" (10 1/2" (including flange) x 4 1/2" x 2 3/16" (22 cm (27 cm (including flange) x 11 cm x 6 cm)
  • RU: 5

WEIGHT
3 lbs (1.4 kg)

POWER

  • Self-powered when used with 110/220 VAC applications
  • Power input options (for control board):
    - 120/240V ~, 50-60 Hz, 0.05/0.025A
    - 12 VDC, 0.2A max
  • Power output per relay
    - 20A @ 120/240V ~, 50-60 Hz (RESISTIVE LOAD)
    - 6A @ 277V ~, 50-60 Hz (FLUORESCENT BALLAST)
    - 1 HP @ 120V ~, 50-60 Hz (INDUCTIVE LOAD)
    - 2 HP @ 240V ~, 50-60 Hz (INDUCTIVE LOAD)
    Total Current through both relays CANNOT exceed 20 amp.

ENCLOSURE
Metal with black matte finish, knockouts for conduit

INPUTS

  • 4 closure inputs, operation defined by mode
  • One IR remote sensor input
  • Motor Control mode alternates between the timed operation of the two power relays
  • Power Control mode allows independent control of both power relays

INPUT POWER SWITCH (S1)

  • Set this switch according to the high voltage wiring that will be connected to terminals 5 and 6 on P1.
  • Set switch S1 to the line input voltage value used before applying power to the UPC20+

HIGH VOLTAGE TERMINAL BLOCK (P1)
High voltage input and output wiring for motor or power control.

LOW VOLTAGE AND CONTROL TERMINAL BLOCK (P2)
Contact closure, open-collector or CMOS logic level remote control wiring Inputs 5 - 8 are referenced to the common connection at pin 4

JUMPER JP1
Sets control mode of the unit to contact closure or remote sensor serial data

TEST SWITCHES (PB1 AND PB2)
Provides local operation of relays K1 and K2 for testing power circuits or motors connected to the relay terminals. An LED indicates relay power applied

MOTOR TIME DELAY POTENTIOMETER (R8)
Only used in motor control modes. User adjusted for setting relay release time between 0 and 90 seconds

DIP SWITCH (S2)
Provides selection of control mode options

CONTROL INPUTS

  • 4 closure inputs; operation defined by mode
  • Motor control mode alternates between the timed operation of the two power relays
  • Power control mode allows independent control of both power relays

CONTROL PORTS
(2) 2400 W power relays. Total combined current through both relays is 20 Amps

CERTIFICATIONS
UL, C-UL, CE

ENVIRONMENTAL
Operating/Storage Temperature: 55º C

NAME DESCRIPTION PART #
PS2.8 2.8 A Power Supply (FG423-05)