NX Series (X200) NX/MCP/DVX/DGX Master Firmware v1.6.160

Last Updated: May 16, 2018

 

----------------------------------------------------------
Prerequisites
----------------------------------------------------------

When upgrading from 1.3.106 or earlier, you must first upgrade to 1.4.90.

----------------------------------------------------------
Programming Information
----------------------------------------------------------

Use of these new Authentication keywords requires Netlinx.axi v1.62.
The NetLinx language supports the following new Authentication keywords:
TLS_CLIENT_CLOSE
TLS_CLIENT_OPEN
For details on the new keywords, please see the NetLinx Language Reference Guide.

----------------------------------------------------------
Changes in this release
----------------------------------------------------------

- This release adds support for 4K/60 HDMI Input/Output boards in
  Enova DGX 100 Series Platform:  FG1061-542,. DGX-I-HDMI-4K60 and
  FG1061-552, DGX-O-HDMI-4K60.
- The IPv6 address of an AMX Master is now consistently reported from NetLinx Studio,
  telnet and the web.
- On the MCP-106 and MCP-108, the last known good date and time are now restored from a
  local file on power cycles.
- Excessive memory usage using IP_CLIENT_OPEN(…) from NetLinx is now fixed.
- Enable password changes for users who’s type is Device.
- Fix inconsistencies found on the display of the IPv6 address on the front panel display
  of the NX-4200.
- Panel logs reported to the master contained extra characters. Now fixed.
- Allow FTP access when remote LDAP is enabled.
- The default NTP servers have been changed. After updating
  to this release, from the Telnet CLI, run the "reset ntp"
  command and then reboot the master.
- Removed unauthorized file access when using "list" and
  "show audit".
- Prevent reboot of master when TLS_CLIENT_OPEN is issued
  to non-connected TLS socket.
- Removed superuser requirement for "clean disk" and reinstated "clean doc" alias
- Fixed FILE_OPEN issue where file would fail to open if it did not already
  exist even though FILE_RW_NEW was specified.
- Fixed relative path navigation.
- Added removal of HTTPS keystore and 802.1x certificates
  when using "reset factory".
- Fixed inconsistency in firmware versions reported by
  "manage firmware" and "report firmware".
- Fixed high password complexity.

----------------------------------------------------------
Known Issues
----------------------------------------------------------

- The following RMS SDKs are not compatible with 1.5.68 and higher:
  RMS SDK 4.0-4.3.26, RMS SDK 4.4.* and RMS SDK 4.5.*    

 

Previous Versions


Related Products

  • DVX-2210HD

    4x2 All-In-One Presentation Switchers with NX Control (Multi-Format, HDMI Inputs)
  • NX-3200

    NetLinx NX Integrated Controller
  • NX-2200

    NetLinx NX Integrated Controller
  • NX-1200

    NetLinx NX Integrated Controller
  • MCP-108

    Massio™ 8-Button ControlPad with Knob (US, UK, EU)
  • MCP-106

    Massio™ 6-Button ControlPad (US, UK, EU)
  • DGX800-ENC

    Enova® DGX 800 Enclosure
  • DGX6400-ENC

    Enova® DGX 6400 Enclosure
  • DGX3200-ENC

    Enova® DGX 3200 Enclosure
  • DGX1600-ENC

    Enova® DGX 1600 Enclosure
  • DVX-3256HD

    10x4 All-In-One Presentation Switchers with NX Control (Multi-Format, HDMI, 4 DXLink™ Inputs)
  • DVX-3255HD

    10x4 All-In-One Presentation Switchers with NX Control (Multi-Format, HDMI, DXLink™ Inputs)
  • DVX-3250HD

    10x4 All-In-One Presentation Switchers with NX Control (Multi-Format, HDMI Inputs)
  • DVX-2255HD

    6x3 All-In-One Presentation Switchers with NX Control (Multi-Format, HDMI, DXLink™ Inputs)
  • DVX-2250HD

    6x3 All-In-One Presentation Switchers with NX Control (Multi-Format, HDMI Inputs)
  • NX-4200

    NetLinx NX Integrated Controller

Previous Versions