Analog Input Resolutions NOTE: Input resolutions supported @60Hz refresh rates are also supported @59.94Hz.
Supports most common HD up to 1920x1200.
Output Resolutions: Matched to inputs.
Analog-To-Digital Conversion: 8-bit 165 MHz per each of three color channels NOTE: The N1115-WP does not accept Composite or S-Video (YC).
Color Space: 4:2:2
*These signal types are supported through a passive adapter.
Input Signal Types: Embedded audio on HDMI (DVI-D through adapter) or Analog Stereo
Output Signal Types: Ethernet
Analog Audio Format: 8ch PCM, Stereo 2-channel
Analog-To-Digital Conversion: 16-bit 32 kHz, 44.1 kHz and 48 kHz
Latency: 10 ms at 60 fps
Bandwidth: 840 Mb/s (varies with resolution)
Note: This is the combined encode plus decode latency. Total latency from source to screen will also include any network latency.
Note: Scaling adds one frame of latency (17ms at 60fps).
Ethernet: 10/100/1000 Mbps, auto-negotiating, auto-sensing, full/half duplex, DHCP, Auto IP, and Static IP
HDMI: HDCP, EDID management
8-wire RJ45 female
10/100/1000 Mbps 10/100/1000Base-T auto-sensing gigabit Ethernet switch port
Provides the network connection, network AV video, and power to the Encoders and Decoders
HDMI IN: HDMI video input
VGA IN: DB15 analog input
USB IN - Host: USB-B host input
USB IN - Maintenance: USB-Mini maintenance input
Controls and Indicators - Front Panel
Press to initiate a 'warm restart' causing the processor to reset, but not lose power. A reset does NOT affect the current settings
POWER LED: On solid (green) when operating power is supplied (via PoE or local power supply)
AUDIO LED: On (green) when audio is transmitting.
ANALOG VIDEO LEDs: On (green) when analog source is available and transmitting.
DIGITAL VIDEO LED: On (green) when video source is available and transmitting
HDCP LED: On (green) when the source is using HDCP
STREAM LED: On (green) when the unit is streaming video
STATUS LED: Flashing (green) when the unit is active.
LINK/ACT LED: Flashing (yellow) when network traffic is being sent or received.
Power over Ethernet
Can be powered via a PoE switch or other equipment with a PoE source. Conforms to IEEE 802.3af Class 3 (802.3at Type 1)
Point-to-point applications between the encoder and a decoder requires a PoE injector to power the wallplate encoder.
Note: In order for the unit to receive Power over Ethernet (PoE), it must be connected to a switch or other equipment that has a PoE PSE (Power Sourcing Equipment) port. Warning: Do not run wiring that is connected to a PoE PSE port outside of the building where the PSE resides. It is for intra-building use only.
Temperature (Operating): 32° to 104°F (0° to 40°C)
Temperature (Storage): -22° to 158°F (-30° to 70°C)
Humidity (Operating): 10% to 90% RH (non-condensing)
Humidity (Storage): 0% to 90% RH (non-condensing)
Heat Dissipation: Up to ~26 BTU/hr
Dimensions (HWD): 4.06" x 3.5" x 2.25" (10.31 cm x 8.84 cm x 5.72 cm)
Weight: .75 lb (0.34 kg)
Airflow: Natural convection via vent openings on front, back, and top
Mounts onto standard 2 gang US back boxes
Mounts into standard décor style wallplates (not included)
Regulatory Compliance: FCC, CE, and NTRL
Compatible with NMX-ENC-N1222, NMX-ENC-N1233, NMX-ENC-N1512, and NMX-NVR-N6123