Cập nhật lần cuối: 16 Thg 9
Product Name: Enova DVX-2265-4K, DVX-3266-4K
FG #: FG1906-0201, AMX-FG106-0202, FG1906-0401, AMX-FG1906-0402
Current Firmware Version: 2.0.4
Release Date: 12/14/23
Device ID: 0x021A, 0x21D
----------------------------------------------------------
Table of Contents
----------------------------------------------------------
1. Prerequisites
2. Features added in this release
3. Fixes in this release
4. Known Issues
5. Programming Information
----------------------------------------------------------
Prerequisites
----------------------------------------------------------
- Requires Controller Firmware 1.6.200 or 1.8.151 (or later - preferred)
- Requires 4K60 DXLink endpoints v1.8.3 or later
- Compatible with legacy DX-TX endpoint v1.8.47
- Compatible with legacy DX-RX endpoint v1.13.43
- Compatible with legacy DX-RX-4K endpoint v2.2.32
----------------------------------------------------------
Features added in this release
----------------------------------------------------------
- Added support for new DXLink 4K60 DWP TX (requires v1.8.171 or later)
Added in previous 2.0.1 release
- None
Added in previous 2.0.0 release
- None
Added in previous 1.9.9 release
- Added API to display 5002 firmware update status in Online Tree or in WebGUI System/Devices option
(WebGUI monitoring requires NX Controller v1.8.151 or later)
Added in previous 1.9.7 release
- None
Added in previous 1.9.4 release
- Added ability for 5002 Uboot version to be displayed in Netlinx Studio as "Dxlink Boot (V1.0.x)"
Added in previous 1.9.3 release
- Added ICSP commands to enable PUBLIC LAN IP on DXLink ports for legacy or HDBT endpoints
-- Send Commands sent to 5002:x:0 where x is the input or output DXlink port
-- DXLINK_IN_LAN-<PRIVATE/PUBLIC> //defaults to PRIVATE
-- ?DXLINK_IN_LAN
-- DXLINK_OUT_LAN-<PRIVATE/PUBLIC> //defaults to PRIVATE
-- ?DXLINK_OUT_LAN
-- Note: This does not apply to DXLink 4K60 TX/RX - They will continue to get "port specific"
AutoSetup PRIVATE IP assignments by default unless AutoSetup is disabled
- Added ICSP commands to set/get the Real Time Clock of 5002 device
-- This aids troubleshooting by adding the current date/time to 5002 log entries
-- Setting does not persist over a power cycle but can be included in the 5002 online event
-- Send Commands sent to 5002:1:0
-- LOG_RTC-YYYY/MM/DD hh:mm:ss //to set the Real Time Clock setting of 5002 device
-- ?LOG_RTC //to get the Real Time Clock setting of 5002 device
----------------------------------------------------------
Fixes in this release
----------------------------------------------------------
- Fixed issue where the logo would not show after disconnecting the input route of an output
Fixed in previous 2.0.1 release
- Fixed issue where the logo would not show after switching beween unused/empty inputs or after
reboot if routed input was unused/empty
- Fixed issue where TCP bound 4K60 DXLink TX/RX would not come online consistently after DVX
reboot and the DXLink cable had to be hotplugged or the DXLINK ETH command had to be toggled
to get the endpoints to come online again
- Fixed issue where HDMI Mirrored output AUDIO was not present after a DVX reboot and the group
had to be reselected
Fixed in previous 2.0.0 release
- Fixed issue causing DVI sources to have distorted text when going through the DVX output scaler
Fixed in previous 1.9.9 release
- Corrected issue where private MAC addresses could be visible on the LAN port for a few seconds
during system boot and/or reconnection of DXLink devices
Fixed in previous 1.9.7 release
- Fixed issue that caused the DVX Fan Speed to ramp to maximum inadvertantly
- Change default FAN_CONFIG setting to be to AUTO rather than MANUAL
- Correct ?FAN_SPEED and ?TEMP response to be same as legacy DVX series
Note: ICSP commands will provide correct response but WebGUI will require refresh/update
- Improved DXLink 4K60 TX/RX online consistency during bootup
Fixed in previous 1.9.4 release
- Fixed asynchronous video status feedback
Fixed in previous 1.9.3 release
- Optimized upgrade process to prevent upgrade failures of individual components
- Fixed issue to ensure DXLink Ethernet is automatically disabled when connecting to another DVX 4K system
- Fixed ICSP processing issue resulting in random 5002 offline/lockup due to heavy ICSP traffic
- Added fix for 5002 offline issue during system bootup
- Fixed issue leading to video loss/lockup over time
- Improved DXLink Quality reporting to make it consistent with other DXLink products
- Improved Video Details reporting for DXLink 2K RX
- Added fix to minimize LAN/ICSLAN IP crossing networks during bootup
-- Note: Final fix requires Service Tech to perform manual "Uboot Upgrade" via internal USB
- Corrected issue to now allow input of 0 for Level 50 and 51 for Disconnect
- Fixed Audio Encoding issue of the HDMI input always reporting as PCM
- Fixed Video Output Configuration settings to show proper default values after using Restore Defaults
----------------------------------------------------------
Known Issues
----------------------------------------------------------
- Duet Modules may not run correctly in 1.8.x NX Controller versions prior to version 1.8.107. This was fixed in 1.8.107 but an earlier
version (1.6.200) was released which also corrected the duet module loading issues. (check help.harmanpro.com for these versions)
- AutoSetup in the DVX 4K60 systems is only designed to work with DX-TX-4K60 and DX-RX-4K60. It will not work with legacy 2k DXLink endpoints
at all and may be intermittent with 4k30 RX endpoints requiring a hotplug after system boot.
- DVX-4K DXLink output cannnot pass video to a DGX 2K DXLink input board
- Non-4K60 DXLink endpoints may not come online after a DVX reboot and require the DXLink Ethernet to be toggled using:
-- DXLINK_IN_ETH-<OFF/AUTO> for TXs
-- DXLINK_ETH-<OFF/AUTO> for RXs
----------------------------------------------------------
Programming Information
----------------------------------------------------------
- It is recommended to disable any Netlinx program (i.e. turn DIP switch 1 ON and reboot) and then begin the firmware transfer
- Send the kit and after the transfer completes the DVX-4K should reboot and begin upgrading each component that doesn't match the kit manifest
- Upgrade times may vary from 15min to nearly 2hrs depending on the starting firmware and number of components needing updating
- Send ?FWVERSION before and after the upgrade to have a record of the beginning and ending version status to make sure all components upgrade properly
- If any parts don't update correctly, send the kit again and check the ?FWVERSION again (have this info available if contacting Tech Support)
--[FWVERSION-ARM_V2.0.4 DSP_V1.2.4 CPLD_V1.0.4 STM32_V2.0.3 Scaler1_V1.4.8 Scaler2_V1.4.8 Scaler3_V1.4.8 Scaler4_V1.4.8]
--[FWVERSION-In_EP1_V4.0.0 In_EP2_V4.0.0 In_EP3_V4.0.0 In_EP4_V4.0.0 In_Valens1_V7.4.52 In_Valens2_V7.4.52 In_Valens3_V7.4.52 In_Valens4_V7.4.52]
--[FWVERSION-In_DSC1_V9.3.5 In_DSC2_V9.3.5 In_DSC3_V9.3.5 In_DSC4_V9.3.5]
--[FWVERSION-Out_Valens1_V7.4.52 Out_Valens2_V7.4.52 Out_DSC1_V1.3.3 Out_DSC2_V1.3.3]
tải xuống
