• Digital Video Input:
• HDMI, DVI-D, Dual-Mode DisplayPort (DP++), RGB/VGA
• DVI-D and Dual-Mode DisplayPort (DP++) are supported through a passive adapter
• Analog Video Input
• HD-15 VGA, Component
• Component is supported through a passive adapter
• Video Output
• Network video over Ethernet via RJ45 port or fiber via 1G SFP port, HDMI, DVI-D
• DVI-D is supported through a passive adapter
• Formats: HDMI, DVI-D (through adapter), HDCP content protection support, RGBHV, YPbPr
• Progressive Input Resolutions
• Supports most common HD up to 1080p60.
• *720x480 @ 59Hz, 640x480 @ 60Hz, *720x480 @ 60Hz, *720x576 @ 50Hz, 800x600 @ 56Hz, 800x600 @ 60Hz, *1280x720 @ 50Hz, *1280x720 @ 59Hz, *1280x720 @ 60Hz, 1024x768 @ 60Hz, 1280x800 @ 60Hz, 1440x900 @ 60Hz, 1680x1050 @ 60Hz, 1920x1080 @ 24Hz, 1920x1080 @ 25Hz, 1920x1080 @ 29Hz, 1920x1080 @ 30Hz, *1920x1080 @ 50Hz, *1920x1080 @ 59Hz, *1920x1080 @ 60Hz, *1920x1080i @ 50Hz, *1920x1080i @ 59Hz, *1920x1080i @ 60Hz
• Interlaced Input Resolutions
• Supports 1080i60.
• *720x480 @ 59Hz, 640x480 @ 60Hz, *720x480 @ 60Hz, *720x576 @ 50Hz, 800x600 @ 56Hz, 800x600 @ 60Hz, *1280x720 @ 50Hz, *1280x720 @ 59Hz, *1280x720 @ 60Hz, 1024x768 @ 60Hz, 1280x800 @ 60Hz, 1440x900 @ 60Hz, 1680x1050 @ 60Hz, 1920x1080 @ 24Hz, 1920x1080 @ 25Hz, 1920x1080 @ 29Hz, 1920x1080 @ 30Hz, *1920x1080 @ 50Hz, *1920x1080 @ 59Hz, *1920x1080 @ 60Hz, *1920x1080i @ 50Hz, *1920x1080i @ 59Hz, *1920x1080i @ 60Hz
• Analog Input Resolutions
  Input resolutions supported @60Hz refresh rates are also supported @59.94Hz
• Supports most common HD up to 1080p60.
• *720x480 @ 59Hz, 640x480 @ 60Hz, *720x480 @ 60Hz, *720x576 @ 50Hz, 800x600 @ 56Hz, 800x600 @ 60Hz, *1280x720 @ 50Hz, *1280x720 @ 59Hz, *1280x720 @ 60Hz, 1024x768 @ 60Hz, 1280x800 @ 60Hz, 1440x900 @ 60Hz, 1680x1050 @ 60Hz, 1920x1080 @ 24Hz, 1920x1080 @ 25Hz, 1920x1080 @ 29Hz, 1920x1080 @ 30Hz, *1920x1080 @ 50Hz, *1920x1080 @ 59Hz, *1920x1080 @ 60Hz, *1920x1080i @ 50Hz, *1920x1080i @ 59Hz, *1920x1080i @ 60Hz
• Output Resolutions: Matched to inputs
• Analog-To-Digital Conversion: 8-bit 165 MHz per each of three color channels
  The N3132 Encoder does not accept Composite or SVideo (YC)

*supported in component mode

• Input Signal Types: Embedded audio on HDMI (DVI-D through adapter) or Analog Stereo (Balanced or Unbalanced)
• Output Signal Types:
• Ethernet, Embedded audio on HDMI or DVI-D (through adapter)
• HDMI output refers to pass-through video on the HDMI OUT port
• HDMI Audio Formats: Stereo 2-channel
• Analog Audio Formats: Stereo 2-channel
• Analog-To-Digital Conversion: 16-bit 32 kHz, 44.1 kHz and 48 kHz

NOTE: HDMI output refers to pass-through video on the HDMI OUT port.

• Latency: 175 ms at 60 fps

Note: This is the combined encode plus decode latency. Total latency from source to screen will also include any network latency.

Note: Scaling adds one frame of latency (17ms at 60fps)

• Ethernet
• P0
• 10/100/1000 Mbps, auto-negotiating, auto-sensing, full/half duplex, DHCP, Auto IP, and Static IP
• P1
• 1 Gbps port which accepts compatible fiber transceivers or direct attach cables (fiber or copper cabling)
• HDMI: HDCP, EDID management

• +12V 2A: One 12 Volt DC power input.
• P0
• 8-wire RJ45 female
• 10/100/1000 Mbps 10/100/1000Base-T auto-sensing gigabit Ethernet switch port
• Provides the network connection, network AV video, and power to the Encoders and Decoders
• P1
• SFP port (SFP fiber transceiver or direct attach cable not included)
• Provides the network connection and network AV video
• IR
• 2-pin terminal Phoenix connector
• Provides Infrared (IR) output only (33-60 kHz; typically 39 kHz). Emitter may be necessary (not included)
• RS232
• 3-pin terminal Phoenix connector
• Provides a serial control interface. Full duplex communication. Available terminal speed settings: 9600-115200 baud rate
• AUDIO
• 5-pin terminal Phoenix connector
• Provides user-selectable balanced/unbalanced input. Dedicated audio input
• HDMI OUT: HDMI video output (passive pass-through from HDMI IN)
• HDMI IN: HDMI video input
• VGA IN: DB15 analog input
• USB connector (front panel): One USB-A control input

• RESET Button
• Recessed pushbutton
• Press to initiate a 'warm restart' causing the processor to reset, but not lose power. A reset does NOT affect the current settings
• ID Button
• Recessed pushbutton
• Press to send a notification out on the network to identify the unit (the notification causes a pop-up dialog in N-Able and N-Command)
• POWER LED
• On solid (green) when operating power is supplied (via PoE or local power supply)
• This activity is also shown by the PWR LED on the rear panel
• STATUS LED
• On flashing (green) when there is software activity
• This activity is also shown by the STAT LED on the rear panel

• PWR LED: Same as POWER LED described above
• HDMI LED: On (green) when there is a connection to a valid video source
• STAT LED: Same as STATUS LED described above
• STRM LED: On (green) when the unit is streaming video

• Temperature: 32° to 104°F (0° to 40°C)
• Humidity: 10% to 90% RH (non-condensing)
• Heat Dissipation: Up to ~44 BTU/Hr

• Regulatory Compliance: FCC, CE, and NTRL
• Recommended Accessories: NMX-ACC-N9206 (FGN9206), 2RU Rack Mount Cage with Power for Six SVSI N-Series Card Units