• Signal Types
• Video Input: Network video over Ethernet via RJ45 port
• Video Output: HDMI, DVI-D (through adapter)
• Formats
• HDMI, DVI-D (through adapter), HDCP content protection support
• Output Resolutions
• Supports most common HD up to 4096x2160. See website for all supported resolutions.

• Signal Types
• Input Signal Types: Network audio over Ethernet via RJ45
• Output Signal Types: Embedded audio on DVI-D or HDMI (through adapter)
• HDMI Audio Formats: 8ch PCM
• Analog Audio Format: Stereo 2-channel
• Digital-to-Analog Conversion: 16-bit 32 kHz, 44.1 kHz and 48 kHz (matched to network audio stream settings)

• Uncompressed:
• 25 ms at 60 fps
• 50 ms at 30 fps
• JPEG2000:
• 50 ms at 60 fps
• 100 ms at 30 fps

Note: This is the combined encode plus decode latency. Total latency from source to screen will also include any network latency.

Note: Scaling adds one frame of latency (16ms at 60fps)

• Ethernet
• P0: 10/100/1000 Mbps, auto-negotiating, auto-sensing, full/half duplex, DHCP, Auto IP, and Static IP
• P1: Full duplex, DHCP, Auto IP, and Static IP 10 Gbps port which accepts compatible fiber transceivers or direct attach cables (fiber or copper cabling)

• +12V 2A: One 12 Volt DC power input
• P0
• 8-wire RJ45 female
• 10/100/1000 Mbps 10/100/1000Base-T auto-sensing gigabit Ethernet switch port
• Provides network control connections and compressed network AV output
• P1
• SFP+ port (SFP+ fiber transceiver or direct attach cable not included) for uncompressed or compressed networked AV and allows network control connections
• IR
• 2-pin terminal Phoenix connector
• Provides Infrared (IR) output only (33-60 kHz; typically 39 kHz). Emitter may be necessary (not included)
• RS232
• 3-pin terminal Phoenix connector
• Provides a serial control interface. Full duplex communication. Available terminal speed settings: 9600-115200 baud rate
• AUDIO
• 5-pin terminal Phoenix connector
• Dedicated audio output
• HDMI OUT: HDMI video output
• USB connectors (front panel): USB-B control input and two USB-A control inputs Currently only the USB-A connectors are supported in software for HID devices

• RESET Button
• Recessed pushbutton
• Hold 30 seconds for a factory reset of all settings, including IP address settings
• Press to initiate a 'warm restart' causing the processor to reset, but not lose power. A reset does NOT affect the current settings
• ID Button
• Recessed pushbutton
• Press to send a notification out on the network to identify the unit (the notification causes a pop-up dialog in N-Able and N-Command)
• POWER LED
• On solid (green) when operating power is supplied (via PoE or local power supply)
• This activity is also shown by the PWR LED on the rear panel
• STATUS LED
• On flashing (green) when there is software activity
• This activity is also shown by the STAT LED on the rear panel

• PWR LED: Same as POWER LED described above
• HDMI LED: On (green) when there is a connection to a valid display
• STAT LED: Same as STATUS LED described above
• STRM LED: On (green) when the unit is streaming video

• Regulatory Compliance: FCC, CE, and NTRL
• Recommended Accessories:
• NMX-ACC-N9206 (FGN9206), 2RU Rack Mount Cage with Power for Six SVSI N-Series Card Units

Audio/video content sent from the encoder is compatible with the following products:

• NMX-ENC-N2151 (FGN2151-XX) JPEG 2000 4K UHD Video over IP Encoder with KVM
• NMX-ATC-N4321 (FGN4321-XX) Audio Transceiver, 2 Channel
• N4000 Audio only
• NMX-NVR-N6123 (FGN6123) Network Video Recorder
• Record and playback single stream only. Archive functionality is not supported.