Last Updated: 9月28日
Product Name: Enova DGX 8/16/32/64 Enclosures
=========== ====================== ======================
FG # Name Description
=========== ====================== ======================
FG1058-08 AVS-ENOVADGX8-ENC Enova DGX 8 Enclosure
FG1058-16 AVS-ENOVADGX16-ENC Enova DGX 16 Enclosure
FG1059-32 AVS-ENOVADGX32-ENC Enova DGX 32 Enclosure
FG1059-33 AVS-ENOVADGX32-ENC-A Enova DGX 32 Enclosure
FG1060-08 DGX8-ENC Enova DGX 8 Enclosure
FG1060-16 DGX16-ENC Enova DGX 16 Enclosure
FG1060-32 DGX32-ENC-A Enova DGX 32 Enclosure
FG1060-64 DGX64-ENC Enova DGX 64 Enclosure
*****************IMPORTANT********************************
If sending this kit to a DGX 8/16/32 with
v1.6.5.13 (or earlier), you MUST FIRST send
the following kit to the Enova DGX enclosure:
"LOAD_BEFORE_SENDING_DGX_KIT.kit"
(This takes around 1 minute to complete)
**********************************************************
IMPORTANT NOTE ABOUT TIME REQUIRED TO UPGRADE:
See the Programming Information section in this
read me for an explanation of how to know when
the upgrade is complete as well as estimates of
the time required for the update to successfully
upgrade. Ignoring this information could cause
your upgrade to fail to complete.
Current Firmware Version: 2.2.12
Build Date: 2017-09-22
Website Availability: EnovaDGX_2.2.12.kit
Device Id: 5002
EnovaDGX KIT file 2.2.12 contains these firmware images:
* Indicates changes since v2.2.8
- MCPU 8 NI-Series v2.6.2.2
- MCPU 16 NI-Series v2.6.2.2
- MCPU 32 NI-Series v2.6.2.2
- MCPU 8 NX-Series v2.8.2.4
- MCPU 16 NX-Series v2.8.2.4
- MCPU 32 NX-Series v2.8.2.4
- MCPU 64 NX-Series v2.8.2.4
- Power BCPU 8 NI-Series v2.2.2.1
- Power BCPU 16 NI-Series v2.2.2.1
- Power BCPU 32 NI-Series v2.2.2.1
- Power BCPU Nx-Series v2.4.1.6
- DGX Center Board v2.0.4.3
- SC Fiber Input v2.0.0.6
- SC Fiber Output v2.0.1.2
- DVI/HDMI Input v1.4.3.2*
- DVI/HDMI Output v1.4.3.3*
- DXLink Input v1.4.6.5*
- DXLink Output v1.4.5.1*
- DGX AIE Board v1.0.0.4
- DGX64 AIE Board v2.0.1.1
- 6p switch v1.0.2.1
- 24p Config v1.2.1.1
- 24p ext Board v1.0.0.2
- DXLink Rx FW v3.0.6.0
- DXLink Tx FW v3.0.6.0
- DXLink Fiber Fw v1.0.1.4
- Output Scaler v1.17
- SRM File v1.0.5.1
- Integrated App v1.2.1.15
----------------------------------------------------------
Prerequisites
----------------------------------------------------------
- NetLinx Studio v4.0 or later
- NI Series Master Firmware v4.2.395 or later
- NX Series (X200) Master Firmware v1.4.90 or later
Endpoints should have the following versions to be compatible
- DXLink DX-TX v1.8.28 or later
- DXLink DX-RX v1.13.34 or later
- DXLink DXF-TX v1.4.12 or later
- DXLink DXF-RX v1.4.17 or later
- Solecis SDX-X10-DX v1.4.9 or later
NOTE: Older TX & RX firmware versions (1.6.xx & 1.9.xx)
are specifically not supported with this DGX kit fw
= = = = = = = = = = = = = = = = = = = = = = = = = = = = = =
! ! ! ! ! ! ! ! ! I M P O R T A N T ! ! ! ! ! ! ! ! ! ! !
= = = = = = = = = = = = = = = = = = = = = = = = = = = = = =
NOTE: This update is only required for an existing Enova DGX
system (running v2.0.2.2 or earlier) IF new DGX 100 series
I/O cards OR endpoints are being added to that system and the
user does not wish to downgrade the new cards or endpoints
to match their existing system firmware. Mixed rev systems
are NOT supported.
It is recommended to update the DGX enclosre/cards first and
then update any attached endpoints to the compatible versions
listed above.
----------------------------------------------------------
Changes in this release
----------------------------------------------------------
HDMI Input
- Corrected issue where AIE state may not report correctly
HDMI/DVI Output boards
- Fixed issue where upstream instability (hotplugs, garbage
video, etc.) could result in HDMI outputs encountering
various video artifacts (sawtooth, posterization, venetian
blinds, black video, etc.)
- Fixed issue where upstream instabiltiy could cause
extracted audio from AIE outputs to drop unexpectedly
DXLink Input
- Fixed issue where async notifications from upstream
Solecis 2K switchers were being blocked
- Fixed issue with HDCP compliance setting when using a
4K WP and the source is disconnected or asleep
- Modify DGX_SHELL>channel command to show freerun res/ref
when no signal present
- Updated firmware to support alternate flash memory parts
NOTE: Boards using these new parts will not function with
firmware earlier than v1.4.6.5 - Do not roll back.
DXLink Output
- Fixed issue where hotplugging Fiber Rx can cause DXLink
output card to reboot
----------------------------------------------------------
Known Issues
----------------------------------------------------------
- A wait of 15seconds is required when Hot Swapping DGX
I/O boards
- DGX Configuration Software
The Scaler tabs may not accurately reflect current
settings with this revision of the output cards but
the scaler settings are being applied when set.
The DGX Config Software has not been tested with any
non-English versions of Windows XP or Windows 7.
- DXLink Tx Fw v3.0.6.0
The ‘show stats’ DGX Shell command (or “show vs100
stats” from the DXLINK TX/RX telnet command) may
report some cable lengths approaching 100m as 255m.
This is a reporting limitation imposed by the chip mfr
for TX v3.0.6.0 and does not affect the functionality.
This applies to any DGX or DVX DXLink output, or any
DXLink TX/MFTX module or wallplate using this version.
- DO NOT USE THE "DGX_SHELL>reboot" command with older
ENOVA DGX 8/16/32 Enclosures with Power-One Power
Supplies that have the new CPU with NX-Series Master.
This WILL cause the cards to not power up and REQUIRE a
hard power cycle of the cage. Power-One supplies may be
identified in the ~scr6v3! or with the
"DGX_SHELL>power INFO" command by model number:
e.g. model: FNP850-12ARG (Power-One Supply)
----------------------------------------------------------
Programming Information
----------------------------------------------------------
- If sending this kit to a DGX 8/16/32 with v1.6.5.13 or
earlier, you MUST FIRST send the following kit to the
Enova DGX enclosure: "LOAD_BEFORE_SENDING_DGX_KIT.kit"
This takes around 1 minute to complete. Once completed,
refresh the System Online Tree and expand the 5002
device to verify that the Integrated Device version is
now at v1.2.1.15 - Then send this DGX kit to complete
the system upgrade
- Upgrade time may take up to 2 hours.
- The only reliable way to monitor the upgrade is to jump
directly to the upgrade status page with the url:
http://master_ipAddr/web/upgrade/systemUpgradeStatus.xml
before initiating the KIT upgrade to monitor the runtime
upgrade status.
- It is recommended that you disable any program running
on the DGX or that you disable any program using the
Enova DGX BCSTunnel service before initiating the Enova
DGX KIT firmware upgrade.
- It is also recommended that you disconnect/disable any
control system using the external serial connection(s)
during any KIT file upgrades.
- After the Upgrade Status page has indicated that the
Enova DGX firmware upgrade was successful and device
5002 has come back online, it is recommended that you
power cycle the DGX to insure all endpoint devices come
back online properly.
- New HDMI/DVI Input boards will only work with v1.0.6.4
image or greater (v2.0.0.10 DGX KIT) or greater due to
hardware design change. It can be identified in the shell
“show” command with a hardware ID of 1 (HW_ID 0x1).
- New DXLink Fiber Input/Output Simplex Boards will
not be compatible with v1.2.0.x DXLink images or older.
Enova DGX KIT v2.0.0.8 or older will fail to load with
these boards present in the system.
下载
