| Video |
- Signal Types
- Digital Video Input: HDMI, DVI-D*, Dual-Mode DisplayPort (DP++)*
- Analog Video Input: HD-15 VGA, Component*
- Video Output: Network video over Ethernet via RJ45 port or via 10G SFP+ port, HDMI, DVI-D*
*Note: these signal types are supported through a passive adapter.
- Formats
- HDMI, DVI-D*, Dual-Mode DisplayPort (DP++)*, HDCP content protection support, RGBHV, YPbPr
*Note: these signal types are supported through a passive adapter.
- Progressive Input Resolutions
- HDMI and DVI (Progressive)
- Pixel clock between 54 MHz - 300 MHz
- Minimum resolution of 1024x768
- Maximum horizontal resolution of 4096 or a vertical resolution of 2160*
- Common acceptable resolutions include: 1024x768p60, 1280x720@60Hz - 720p60, 1600x1200@60Hz, 1920x1080@60Hz - 1080p60, 2560x1440@30Hz - QHD30, 3840x2160@30Hz - UHD30 aka 4K30, 3840x2160(4:2:0)@50Hz (JPEG2000 only), 3840x2160(4:2:0)@60Hz (JPEG2000 only), 4096x2160(4:2:2)@30Hz - DCI 4K30, 4096x2160(4:2:0)@60Hz (JPEG2000 only)
- Interlaced Input Resolutions
- HDMI and DVI (Interlaced)
- 1920x1080@50Hz - 1080i50 (JPEG2000 only)
- 1920x1080@60Hz - 1080i60 (JPEG2000 only)
Note: Interlaced resolutions will be de-interlaced.
- Analog Input Resolutions
- VGA
- Pixel clock between 54 MHz - 165 MHz
- Minimum resolution of 1024x768
- Maximum horizontal resolution of 1920 or a vertical resolution of 1200
- Common acceptable resolutions include: 1024x768@60Hz, 1280x720@50Hz (720p50), 1280x720@60Hz (720p60), 1280x768@60Hz, 1280x800@60Hz, 1280x960@60Hz, 1280x1024@60Hz, 1360x768@60Hz, 1366x768@60Hz, 1400x1050@60Hz, 1440x900@60Hz, 1600x1200@60Hz, 1680x1050@60Hz, 1920x1080@50Hz (1080p50), 1920x1080@60Hz (1080p60), 1920x1200@60Hz (reduced blanking)
- Component
- HD up to 1080p60
- 1920x1080@50Hz - 1080i50 (JPEG2000 only)
- 1920x1080@60Hz - 1080i60 (JPEG2000 only)
- Output Resolutions: Matched to inputs*
*Note: Input resolutions supported @60Hz refresh rates are also supported @59.94Hz
*Note: The N2151 Encoder does not accept Composite or S-Video (YC)
- Color Space
- 4:2:2 Resolutions up to 4K30
- 4:2:0 4K60
|
| Audio |
- Signal Types
- Input: Embedded audio on HDMI (DVI-D through adapter) or Analog Stereo (Balanced or Unbalanced)
- Output: Ethernet, Embedded audio on HDMI or DVI-D (through adapter)*
*HDMI output refers to pass-through video on the HDMI OUT port
- Formats
- HDMI: 8ch PCM
- Analog: Stereo 2-channel
- Analog-To-Digital Conversion: 16-bit 32 kHz, 44.1 kHz and 48 kHz
|
| Latency |
Uncompressed:
- 25 ms at 60 fps
- 50 ms at 30 fps
JPEG2000:
- 50 ms at 60 fps
- 100 ms at 30 fps
Note: This is the combined encode plus decode latency. Total latency from source to screen will also include any network latency
Note: Scaling adds one frame of latency (17ms at 60fps) |
| Bandwidth |
- Uncompressed: 4000 Mb/s at 4K30 4:2:2
- JPEG2000: 200 to 600 Mb/s*
- Recommend 200-300 Mb/s for motion video
- Recommend 500-600 Mb/s for computer graphics
- *Note: Minimum bandwidth is 50 Mb/s for resolutions <= 1080p60
|
| Communications |
- Ethernet
- PO
- 10/100/1000 Mbps, auto-negotiating, auto-sensing, full/half duplex, DHCP, Auto IP, and Static IP
- P1
- 10 Gbps port which accepts compatible fiber transceivers or direct attach cables
- HDMI: HDCP, EDID management
|
| Ports |
- +12V 2A: One 12 Volt DC power input
- PO
- 8-wire RJ45
- 10/100/1000 Mbps 10/100/1000Base-T auto-sensing gigabit Ethernet switch port
- Provides the network connection and JPEG2000 compressed video
- P1
- 10 Gb/s SFP+ port (SFP+ fiber transceiver or direct attach cable not included)
- Provides the network connection and uncompressed networked AV video
- IR
- 2-pin terminal Phoenix connector
- Provides Infrared (IR) output only (33-60 kHz; typically 39 kHz). Emitter may be necessary (not included)
- RS232
- 3-pin terminal Phoenix connector
- Provides a serial control interface. Full duplex communication. Available terminal speed settings: 9600-115200 baud rate
- AUDIO
- 5-pin terminal Phoenix connector
- Provides user-selectable balanced/unbalanced input. Dedicated audio input
- HDMI OUT: HDMI video output (passive pass-through from HDMI IN)
- HDMI IN: HDMI video input
- VGA IN: DB15 analog input
- USB connectors (front panel): USB-B control input and two USB-A control inputs
|
| Controls and Indicators - Front Panel |
- RESET Button
- Recessed pushbutton
- Press to initiate a 'warm restart' causing the processor to reset, but not lose power. A reset does NOT affect the current settings
- ID Button
- Recessed pushbutton
- Press to send a notification out on the network to identify the unit (the notification causes a pop-up dialog in N-Able and N-Command)
- POWER LED
- On solid (green) when operating power is supplied (via PoE or local power supply)
- This activity is also shown by the PWR LED on the rear panel
- STATUS LED
- On flashing (green) when there is software activity
- This activity is also shown by the STAT LED on the rear panel
|
| Controls and Indicators - Rear Panel |
- PWR LED: Same as POWER LED described above
- HDMI LED: On (green) when there is a connection to a valid video source
- STAT LED: Same as STATUS LED described above
- STRM LED: On (green) when the unit is streaming video
|
| General |
- Regulatory Compliance: FCC, CE, and NTRL
- Recommended Accessories: NMX-ACC-N9206 (FGN9206), 2RU Rack Mount Cage with Power for Six SVSI N-Series Card Units
|
| FG Numbers |
FGN2151-CD |
Dukungan Konsultan