Terakhir Diperbarui: 06.01.2021
Product Name: N-Series N2300 Video Encoder/Decoder
FG #: FGN2312-SA
FGN2322-SA
Version: 01.01.24
Release Date: 10/15/2020
----------------------------------------------------------
1. Prerequisites
----------------------------------------------------------
- None
----------------------------------------------------------
2. Revision History
----------------------------------------------------------
Version 01.01.24
Remove support for TLS 1.0 and 1.1
Version 01.01.23
Optimize time delay in KVM IP switching
Version 01.01.21
Fix webpage security issue with POST
Version 01.01.20
Make more DHCP attempts during unit boot up
Add new command to create dhcp timing extended
New command "setSettings:dhcpAgain:300", after 300 seconds after
the unit assigns itself an auto IP, the DHCP process
would start again. User can modify the 300 to value they need.
lower limit is 60 seconds, to allow linkLocal to work properly
To disable the setting, "setSettings:dhcpAgain:0"
Version 01.01.19
Fix broken IR control with long IR codes
Version 01.01.18
Improve the "Unsolicited Status" feature
Version 01.01.17
Enable scaler of decoder after factory restoration
Version 01.01.16
Support 2560x1440
Fix decoder reboot when it's routed to encoder with no source connected
Support units with new analog audio chip
Version 01.01.15
Improve VGA/HDMI startup time
Implement option to give VGA or HDMI input priority
Add Identify button to web page that displays IP address on decoder
Version 01.01.14
Improve KVM connection recovery on reboot.
Change audio stream ttl to default to 64
Implement KVM retry
Make analog audio startup delay optional
Add optional encoder reboot on audio input failure
Version 01.01.05
Fix issue with uploading odd host/local play images
Fix issue with debug log startup
Fix issue with KVM reconnecting on encoder or decoder restart
Improved button feedback on webpages
Treat stream 0 as a stream instead of as a local play command
Add HDCP connection status to the decoder
Resolved audio stream compatibilty issues with other N-Series units
Fixed audio multicast address calculation
Add option to blank video during switch
Don't issue NAct plug events on bootup
Improved audio networking to avoid audio pops when video rate goes up
Delay audio startup to avoid audio artifact after stream switch
Add option to disable video genlock which causes some monitors to stutter the audio
Improve decoder robustness
Version 00.04.22
Fix audio multicast address for non-interleaved mode
Version 00.04.21
Fix 32K and 44.1K audio issue that occurred with selected monitors
Default output to RGB to avoid the green screen
Default KVM to on to match spec
Version 00.04.20
Fix audio pop on decoder analog audio output
Add 1920x1200 to EDID (requires reloading default EDID).
Add latest netlinx support and add netlinx version to the webpage
Version 00.04.15
Fix audio stutter issue
Add control for video genlock
Fix issue with audio channel count change crashing encoder.
Fix issue with log overflowing on debug start
Add support for DNS
Version 00.04.11
Provide sync override feature for monitors that are sensitive to clock changes.
Fixed decoder issue caused by selecting stream 0. Now is the same as localPlay.
Fix IR upload for N2300 devices
Version 00.04.08
Fix loss of I-Frame requests on encoder stream restart
Version 00.04.04
Add commands for output volume up/down
Support secure ports only mode
Clean up xml status file
Improve encoder HDCP robustness
Add line input volume control
Fix decoder reboot on stream switch
Suport RGB 4K resolution mode
Block unknown multicast streams from the swtich
Support Harman serial number format
Fix network lockup when switching into DHCP mode
Improved Netlinx support
Improved decoder stability
----------------------------------------------------------
3. Known Issues
----------------------------------------------------------
On soft reboot, some devices lose KVM connectivity and require a hard decoder reboot
If DHCP is first enabled on a network without a DHCP server, the unit reboots and the
setting is lost. If the unit is running DHCP but is rebooted on a network without a
DHCP server, it falls back to autoip correctly.
unduh
