• Digital Video Input: Network video over Ethernet via RJ45 port or fiber via 1G SFP port
• Video Output: HDMI, DVI-D (through adapter)
• Formats: HDMI, DVI-D (through adapter), HDCP content protection support
• Output Resolutions:
• Supports most common HD resolutions up to 1920x1200.
• **720x480 @ 59Hz, 640x480 @ 60Hz, **720x480 @ 60Hz, **720x576 @ 50Hz, 800x600 @ 56Hz, 800x600 @ 60Hz, **1280x720 @ 50Hz, **1280x720 @ 59Hz, **1280x720 @ 60Hz, 1360x768 @ 60Hz, 1366x768 @ 60Hz, 1024x768 @ 60Hz, 1280x800 @ 60Hz, 1152x864 @ 60Hz, 1600x900 @ 60Hz, 1440x900 @ 60Hz, 1280x960 @ 60Hz, 1280x1024 @ 60Hz, ***1600x1200 @ 60Hz, 1680x1050 @ 60Hz, 1920x1080 @ 23Hz, 1920x1080 @ 24Hz, 1920x1080 @ 25Hz, 1920x1080 @ 29Hz, 1920x1080 @ 30Hz, **1920x1080 @ 50Hz, **1920x1080 @ 59Hz, **1920x1080 @ 60Hz, **1920x1080i @ 50Hz, **1920x1080i @ 59Hz, **1920x1080i @ 60Hz, ***1920x1200 @ 60Hz

**supported in component mode

***reduced blanking only

• Input Signal Types: Network video and audio over Ethernet via RJ45 (audio at 48-kHz, standard SVSI audio stream or AES67, user selectable)
• Output Signal Types: Embedded audio on DVI-D or HDMI (through adapter)
• HDMI Audio Formats: 8ch PCM

• Video 50 ms for 720p60
• Video 140ms for 1080p60
• Audio Latency: standard SVSI audio stream = 17 ms (synced to video); AES67 = <1 ms adjustable to 17 ms

Note: This is the combined encode plus decode latency. Total latency from source to screen will also include any network latency.

Note: Scaling adds one frame of latency (17ms at 60fps).

• Ethernet
• P1
• 10/100/1000 Mbps, auto-negotiating, auto-sensing, full/half duplex, DHCP, Auto IP, and Static IP

• +12V 2A: One 12 Volt DC power input
• P1:
• 8-wire RJ45 female
• 10/100/1000 Mbps 10/100/1000Base-T auto-sensing gigabit Ethernet switch port
• RS232:
• 3-pin terminal Phoenix connector
• Provides a serial control interface. Full duplex communication. Available terminal speed settings: 1200-115200 baud rate
• HDMI OUT: HDMI video output

• RESET Button:
• Recessed pushbutton
• Press to initiate a 'warm restart' causing the processor to reset, but not lose power. A reset does NOT affect the current settings

• ID Button:
• Recessed pushbutton
• Press to send a notification out on the network to identify the unit (the notification causes a pop-up dialog in N-Able and N-Command)

• POWER LED:
• On solid (green) when operating power is supplied (via PoE or local power supply)
• This activity is also shown by the PWR LED on the rear panel

• STATUS LED:
• On flashing (green) when there is software activity
• This activity is also shown by the STAT LED on the rear panel

• PWR LED: Same as POWER LED described above
• HDMI LED: On (green) when there is a connection to a valid video source
• STAT LED: Same as STATUS LED described above
• STRM LED: On (green) when the unit is streaming video

• Temperature: 32° to 104°F (0° to 40°C)
• Humidity: 10% to 90% RH (non-condensing)
• Heat Dissipation: Up to ~44 BTU/hr

• Regulatory Compliance: FCC, CE, and NTRL
• Recommended Accessories: NMX-ACC-N9206 (FGN9206), 2RU Rack Mount Cage with Power for Six SVSI N-Series Card Units