DXLink Fiber Receiver Firmware (100 Series Compatible) v1.4.17

Last Updated: 3月15日

IMPORTANT: Scaler settings upgrade warning

If upgrading to DGX firmware v3.0.2x from v3.0.10, and if DXLink RX are configured with non-default scaler settings (scaling mode, aspect ratio and manual resolution), the "PERSISTAV" ICSP command must first be sent to those RX's before performing the firmware upgrade of either the DGX or the RX's in order to preserve their modified settings.

This firmware version requires Enova DGX 100 Series compatibility on connected Enova DGX systems

Please reference the Enova DGX Board and Endpoint Compatibility Instructions on the AMX.com product page for more information

Prerequisites:

  • DXF-TX-xxD v1.4.9 (or later) to support standalone configuration.
  • Enova DGX DXLink Fiber I/O boards must be upgraded to the latest firmware versions (as provided in the DGX kit file listed below).
  • Enova DGX 100 Series enclosures need Enova DGX 800/1600/3200/6400 FW v3.2.5 (or later) and Master FW:
    • SW1060_Master_v1.4.86 (or later)
  • Enova DGX 8/16/32/64 enclosures need Enova DGX 8/16/32/64 FW v2.2.8 (or later) and Master FW:
    • SW1056_Master_v4_2_395.KIT (NI-Series) Shows in Online Tree as "NI Master"
    • SW2106_NX-X200_Master_v1_3_110.kit (NX-Series) Shows in Online Tree as "DGX Master"
  • NetLinx Studio v4.3.1519 or later
  • DGX Configuration Software v1.0.6 or later

Features added in this release (since v1.4.15):

  • Add ICS LAN port public/private control when connected to a DGX through the new 5002 device ENDPOINT_RX_ICSLAN_PORT-Public|Private command.

Fixes in this release (since v1.4.15)

  • Fix handling of value 0 for VIDOUT_SLEEP_DELAY. When set to zero, the display will now immediately be put to sleep when there is no upstream video.
  • Fix orange screen after DGX reboot when using certain displays.

Notable Points:

  • IMPORTANT: Scaler settings upgrade warning If upgrading to DGX firmware v3.0.2x from v3.0.10, and if DXLink RX are configured with non-default scaler settings (scaling mode, aspect ratio and manual resolution), the "PERSISTAV" ICSP command must first be sent to those RX's before performing the firmware upgrade of either the DGX or the RX's in order to preserve their modified settings.
  • On duplex devices, if DIP switch 4 is set ON, the device will be put into unidirectional mode. This will make the duplex device act similarly to a simplex device. Ethernet and control over the fiber link will be disabled. See the instruction manual for details.
  • Please read the documentation in regard to the DIP switches located on the bottom of the Tx/Rx modules before attempting to connect to the network.
  • After a FACTORYAV (ICSP) or RESET FACTORY (telnet) command, a reboot of the RX is required.
  • The RX module uses these solid color screen indications:
    • ORANGE Indicates an HDCP authentication failure with the connected HDMI sink (monitor or other device).
  • If using a hostname in the USB_HID_ROUTE command, the hostname length is limited to 50 characters.

Programming Information

  • DXLink Fiber Receiver Firmware (Enova DGX 100 Series Compatible)
  • This firmware version requires Enova DGX 100 Series compatibility on connected Enova DGX systems
  • Please reference the Enova DGX Board and Endpoint Compatibility Instructions on the AMX.com product page for more information

Previous Versions


相关产品

  • DXF-RX-MMD

    DXLink™ HDMI 多模光纤接收器,双工

  • DXF-RX-MMS

     DXLink™ HDMI 多模光纤接收器,单工

  • DXF-RX-SMD

     DXLink™ HDMI 单模光纤接收器,双工

  • DXF-RX-SMS

     DXLink™ HDMI 单模光纤接收器,单工


Previous Versions