마지막 업데이트: 09월 19일
Release Notes
Product: DXFP-RX-4K60
Description: DXLink 4K60 HDMI Fiber Reciever Module
FG#: FG1010-565-01
FG1010-565-02 (TAA)
File Name: SW1010-565-0X_DXFP-RX-4K60_v1_8_4
Release Date: 6/25/2023
Firmware Version: v1.8.4
1. Prerequisites
2. Features added in this release
3. Fixes in this release:
4. Known Issues
5. Programming Information
6. Notable Points
----------------------------------------------------------
1. Prerequisites
----------------------------------------------------------
- Directly connected DXFP-TX-4K60 v1.8.0 (or later)
- Enova DGX 800/1600/3200/6400 Switcher FW v3.8.25 (or later)
- Enova DVX-2265-4K/DVX-3266-4K Switcher FW v1.9.4 (or later)
- Enova DGX 100 Series & DVX 4K Series Controller FW v1.6.200 or v1.8.97 (or later)
- NetLinx Studio v4.3.1519 (or later)
----------------------------------------------------------
2. Features added in this release:
----------------------------------------------------------
- Added telnet watchdogs to automatically recover endpoint MCU and MasterApp.
Syntax Notes: The command, by itself, queries the current setting. Using on/off after
the command will enable/disable the watchdog
wdlog Queries the count for each Recovery Mechanism (reset factory to clear)
wdmasterapp Queries/enables/disables the masterapp Recovery Mechanism (default is on)
wdmcu Queries/enables/disables the MCU Recovery Mechanism (default is on)
Added in previous release 1.8.3
- Replaced MCU due to EOL parts. FW updated to support new MCU processor
----------------------------------------------------------
3. Fixes in this release:
----------------------------------------------------------
- Fixed a boot-up race condition causing endpoints to randomly be offline after a reboot
- Fixed an RS232 issues with EVEN/ODD parity
- Fixed a memory leak when using RS232 causing the endpoint to lockup over time requiring
reboot to recover
Fixed in previous release 1.8.3
- Fixed issue in TX/RX that caused RS232 strings to be passed out of order
Fixed in previous release v1.8.0
- Fixed Set Connection to Controller to support changing ICSP Port Number and URL hostname
- Fixed async notifications for VIDIN_STATUS
- Fixed Standalone webgui issue to allow changing Static IP and default Gateway together
- Corrected issue causing IR File to be erased on upgrade (IR file should remain on subsequent upgrades)
- TX/ RX to change Eth0 default fallback to prevent conflict with DGX IO card IP scheme
----------------------------------------------------------
4. Known Issues
----------------------------------------------------------
- None
----------------------------------------------------------
5. Programming Information
----------------------------------------------------------
- These devices can be updated using a VNM (Virtual Netlinx Controller)
but the update will go much faster if you can connect to a physical
Netlinx controller. VNM update could take up to 2 hours but
using a physical controller should take less than an hour.
----------------------------------------------------------
6. Notable Points
----------------------------------------------------------
- PLEASE READ the Quick Start Guide in regard to the DIP switches located
on the DXLink 4K60 endpoint before attempting to connect to the network.
- These units have a web interface that is accessible by entering
the URL of the device into a web browser. This may indicate there
is a certificate error, but you can select the Advanced option at
the bottom and proceed to the page. A new certificate can be loaded
via the web interface.
- This web interface is only available when connected to a DXLink 4K60 Receiver.
It is disabled when connected to other endpoint devices or a switcher.
- This device has a default static IP: 192.168.1.2 when it isn't assigned a dynamic IP
by DHCP server or auto-setup porcess.
다운로드
