Video |
- Video Input: Network video over copper via RJ45 port or fiber via 1G SFP port
- Video Output: HDMI, DVI-D (through adapter)
- Formats: HDMI, DVI-D (through adapter), HDCP content protection support
- Input Resolutions
- Supports most common HD up to 1920x1200.
- **720x480@59Hz, 640x480@60Hz, **720x480@60Hz, **720x576@50Hz, 800x600@56Hz, 800x600@60Hz, **1280x720@50Hz, **1280x720@59Hz, **1280x720@60Hz, 1360x768@60Hz, 1366x768@60Hz, 1024x768@60Hz, 1280x800@60Hz, 1152x864@60Hz, 1600x900@60Hz, 1440x900@60Hz, 1280x960@60Hz, 1280x1024@60Hz, 1680x1050@60Hz, 1920x1080@23Hz, 1920x1080@24Hz, 1920x1080@25Hz, 1920x1080@29Hz, 1920x1080@30Hz, **1920x1080@50Hz, **1920x1080@59Hz, **1920x1080@60Hz, **1920x1080i@50Hz, **1920x1080i@59Hz, **1920x1080i@60Hz, ***1920x1200@60Hz
**supported in component mode
***reduced blanking only |
Audio |
- Input Signal Types: Network audio over Ethernet (audio at 48-kHz, standard SVSI audio stream or AES67, user selectable)
- Output Signal Types: Embedded audio on HDMI or DVI-D (through adapter)
- HDMI Audio Formats: 8ch PCM
- Analog Audio Format: Stereo 2-channel
|
滞后时间 |
- Video Latency: 50 ms at 60 fps
- Audio Latency: standard SVSI audio stream = 17 ms (synced to video); AES67 = <1 ms adjustable to 17 ms
Note: This is the combined encode plus decode latency. Total latency from source to screen will also include any network latency.
Note: Scaling adds one frame of latency (17ms at 60fps) |
通讯 |
- Ethernet
- PO: 10/100/1000 Mbps, auto-negotiating, auto-sensing, full/half duplex, DHCP, Auto IP, and Static IP
- P1: 1 Gbps port which accepts compatible fiber transceivers or direct attach cables (fiber or copper cabling)
- HDMI: HDCP, EDID management
|
Ports |
- +12V 2A: One 12 Volt DC power input.
- P0
- 8-wire RJ45 female.
- 10/100/1000 Mbps 10/100/1000Base-T auto-sensing gigabit Ethernet switch port
- Provides the network connection, network AV video, and power to the Encoders and Decoders
- P1
- SFP port (SFP fiber transceiver or direct attach cable not included)
- Provides the network connection and network AV video
- IR
- 2-pin terminal Phoenix connector
- Provides Infrared (IR) output only (33-60 kHz; typically 39 kHz). Emitter may be necessary (not included).
- RS232
- 3-pin terminal Phoenix connector
- Provides a serial control interface. Full duplex communication. Available terminal speed settings: 9600-115200 baud rate
- AUDIO
- 5-pin terminal Phoenix connector
- Provides user-selectable balanced/unbalanced output. Dedicated audio output
- HDMI OUT: HDMI video output
- USB connectors (front panel): One USB-B and two USB-A control inputs
|
Controls and Indicators - Front Panel |
- RESET button
- Recessed pushbutton
- Press to initiate a 'warm restart' causing the processor to reset, but not lose power. A reset does NOT affect the current settings
- ID button
- Recessed pushbutton
- Press to send a notification out on the network to identify the unit (the notification causes a pop-up dialog in N-Able and N-Command)
- POWER LED
- On solid (green) when operating power is supplied (via PoE or local power supply)
- This activity is also shown by the PWR LED on the rear panel
- STATUS LED
- On flashing (green) when there is software activity
- This activity is also shown by the STAT LED on the rear panel
|
Controls and Indicators - Rear Panel |
- PWR LED: Same as POWER LED described above
- HDMI LED: On (green) when there is a connection to a valid video display
- STAT LED: Same as STATUS LED described above
- STRM LED: On (green) when the unit is streaming video
|
环境 |
- Temperature: 32° to 104°F (0° to 40°C)
- Humidity: 10% to 90% RH (non-condensing)
- Heat Dissipation: Up to ~44 BTU/hr
|
General |
- Regulatory Compliance: FCC, CE, and NTRL
- Recommended Accessories:
- NMX-ACC-N9206 (FGN9206), 2RU Rack Mount Cage with Power for Six SVSI N-Series Card Units
|
FG Numbers |
FGN2235A-CD |