Last Updated: Aug 18
Release Notes
DXLink Fiber Receiver Firmware (Enova DGX 100 Series
Compatible)
!!This firmware version requires Enova DGX 100 Series
compatibility on connected Enova DGX systems!!
!!!Please reference the Enova DGX Board and Endpoint
Compatibility Instructions on the AMX.com product
page for more information!!!
FG#:
FG1010-560 (DXF-RX-SMD, DXLink HDMI Single Mode Fiber Receiver, Duplex)
FG1010-561 (DXF-RX-SMS, DXLink HDMI Single Mode Fiber Receiver, Simplex)
FG1010-562 (DXF-RX-MMD, DXLink HDMI Multimode Fiber Receiver, Duplex)
FG1010-563 (DXF-RX-MMS, DXLink HDMI Multimode Fiber Receiver, Simplex)
Release Date: 2017-07-14
Current Released Firmware: v1.4.19
SW1010_56x_AVB_KIT_DXLF_RX_v1_4_19.kit
----------------------------------------------------------
Table of Contents
----------------------------------------------------------
1. Prerequisites
2. Features added in this release
3. Fixes in this release
4. Notable points
5. Programming information
----------------------------------------------------------
1. Prerequisites
----------------------------------------------------------
- DXF-TX-xxD v1.4.9 (or later) to support standalone
configuration.
- Enova DGX DXLink Fiber I/O boards must be upgraded to the
latest firmware versions (as provided in the DGX kit file
listed below).
- Enova DGX 100 Series enclosures need Enova DGX
800/1600/3200/6400 FW v3.0.20 (or later) and Controller FW:
- SW1060 v1.4.72 (or later)
- Enova DGX 8/16/32/64 enclosures need Enova DGX 8/16/32/64
FW v2.2.8 (or later) and Controller FW:
- SW1056 v4_2_395.KIT or later (NI-Series)
Shows in Online Tree as "NI Controller"
- SW2106_NX-X200 v1_3_110.kit or later (NX-Series)
Shows in Online Tree as "DGX Controller"
- NetLinx Studio v4.3.1519 or later
----------------------------------------------------------
2. Features added in this release
----------------------------------------------------------
- Added access to the superuser debug console via the RX's
USB Program on the front panel (baud 115200)
Warning: Use this port carefully as it is possible to
delete firmware or other necessary parameters
----------------------------------------------------------
3. Fixes in this release
----------------------------------------------------------
- Fixed issue causing a factory reset during upgrade to v1.4.18
(Fixed in previous release 1.4.18)
- Fixed offline issue caused by Nessus network scans
- Fixed issue where RX could bounce offline randomly
- Changed the default setting of VIDOUT_SLEEP to ENABLE
- Changed the default setting of VIDOUT_BLANK to BLUE
- Fixed a flash that could occur when source changed from
HDCP to non-HDCP (or on a disconnect of the route)
----------------------------------------------------------
4. Notable points
----------------------------------------------------------
- IMPORTANT: Scaler settings upgrade warning
If upgrading to DGX firmware v3.x.x from v3.0.10,
and if DXLink RX are configured with non-default
scaler settings (scaling mode, aspect ratio and
manual resolution), the "PERSISTAV" ICSP command
must first be sent to those RX's before performing
the firmware upgrade of either the DGX or the RX's
in order to preserve their modified settings.
- On duplex devices, if DIP switch 4 is set ON, the device
will be put into unidirectional mode. This will make the
duplex device act similarly to a simplex device.
Ethernet and control over the fiber link will be disabled.
See the instruction manual for details.
- Please read the documentation in regard to the DIP
switches located on the bottom of the Tx/Rx modules
before attempting to connect to the network.
- After a FACTORYAV (ICSP) or RESET FACTORY (telnet)
command, a reboot of the endpoint is required.
- The RX module uses these solid color screen indications:
ORANGE
Indicates an HDCP authentication failure with
the connected HDMI sink (monitor or other device).
- If using a hostname in the USB_HID_ROUTE command,
the hostname length is limited to 50 characters.
----------------------------------------------------------
5. Programming information
----------------------------------------------------------
- DXLink Fiber Receiver Firmware (Enova DGX 100 Series
Compatible)
- !!This firmware version requires Enova DGX 100 Series
compatibility on connected Enova DGX systems!!
- !!!Please reference the Enova DGX Board and Endpoint
Compatibility Instructions on the AMX.com product
page for more information!!!