DXLink Fiber Transmitter Firmware (100 Series Compatible) v1.4.14

Last Updated: Aug 19

Release Notes

DXLink Fiber Transmitter Firmware (Enova DGX 100 Series
Compatible)

!!This firmware version requires Enova DGX 100 Series
compatibility on connected Enova DGX systems!!

!!!Please reference the Enova DGX Board and Endpoint
Compatibility Instructions on the AMX.com product
page for more information!!!

FG#:
FG1010-360 (DXF-TX-SMD, DXLink Transmitter, HDMI, SM Fiber, Duplex)
FG1010-361 (DXF-TX-SMS, DXLink Transmitter, HDMI, SM Fiber, Simplex)
FG1010-362 (DXF-TX-MMD, DXLink Transmitter, HDMI, MM Fiber, Duplex)
FG1010-363 (DXF-TX-MMS, DXLink Transmitter, HDMI, MM Fiber, Simplex)

Release Date: 2018-02-12
Current Released Firmware: v1.4.14
SW1010_36x_AVB_FW_v1_4_14.kit

----------------------------------------------------------
Table of Contents
----------------------------------------------------------

1. Prerequisites
2. Features added in this release
3. Fixes in this release:
4. Notable Points
5. Programming Information

----------------------------------------------------------
1. Prerequisites
----------------------------------------------------------
- DXF-RX-xxD v1.4.11 (or later) to support standalone
behavior.

- Enova DGX DXLink I/O boards must be upgraded to the latest
firmware versions (as provided in the DGX kit file listed
below).

- Enova DGX 100 Series enclosures need Enova DGX
800/1600/3200/6400 FW v3.2.19 (or later) and Controller FW:

- SW1060 v1.5.78 (or later)

- Enova DGX 8/16/32/64 enclosures need Enova DGX 8/16/32/64
FW v2.2.12 (or later) and Controller FW:

- SW1056 v4_2_395.KIT (NI-Series) Shows in Online
Tree as "NI Controller"

- SW2106_NX-X200 v1_3_110.kit (NX-Series) Shows
in Online Tree as "DGX Controller"

- NetLinx Studio v4.3.1519 or later

- DGX Configuration Software v1.0.6 or later


----------------------------------------------------------
2. Features added in this feature release:
----------------------------------------------------------

- Added ability to allow edid mode to persist in
point to point mode. But it requires a superuser telnet
command be used to set and preserve the EDID mode.

-- Superuser/Debug Console access via Telnet --
1. Telnet to IP of device on port 24
2. Enter username: enova (enter)
3. Enter password: 12amx34 (enter)

-- Superuser/Debug Console access via Program USB --
The Debug Console is also possible via serial connection
to the Program USB port on the front of the Fiber TX.
Connect and open terminal session @ 115200 baud.

-- edid option examples --
AMX> edid (shows the possible edid command options)
AMX> edid get digital_id (gets the current EDID mode)
AMX> edid set digital_load all <all|full|wide>
AMX> edid set mirror_local (uses local HDMI output EDID)
AMX> edid set p2p_preserve on <on|off(default)>
(When on, this preserves the EDID mode when in point
to point mode. When off, the TX resumes its default
mirror downstream EDID behavior on power cycle.)

----------------------------------------------------------
3. Fixes in this patch release:
----------------------------------------------------------
- Fixed video detection issue that could occur when certain
sources are connected or wake from sleep

- Fixed issue in MIRROR_OUT_LOCAL mode where EDID changes
on the local HDMI output were not updating

- Corrected mirror downstream EDID issue where EDID changes
were not mirrored to source without fiber cable hotplug

Fixed in previous 1.4.13 hotfix
- Resolved issue with HSON/HSOFF command sent to DXL-TX

----------------------------------------------------------
4. Notable Points
----------------------------------------------------------

- Please read the documentation in regard to the DIP
switches located on the bottom of the TX/RX modules
before attempting to connect to the network.

- The TX module uses these solid color screen indications:
RED
Indicates an HDCP authentication failure with
the HDMI sink (monitor or other device) connected to the
local output.

----------------------------------------------------------
5. Programming Information
----------------------------------------------------------

- DXLink Fiber Transmitter Firmware (Enova DGX 100 Series
Compatible)

- !!This firmware version requires Enova DGX 100 Series
compatibility on connected Enova DGX systems!!

- !!!Please reference the Enova DGX Board and Endpoint
Compatibility Instructions on the AMX.com product
page for more information!!!

Previous Versions


Related Products

  • DXF-TX-MMD

    DXF-TX-MMD

    DXLink™ Multi-Format Multimode Fiber Transmitter, Duplex
  • DXF-TX-MMS

    DXF-TX-MMS

    DXLink™ Multi-Format Multimode Fiber Transmitter, Simplex
  • DXF-TX-SMD

    DXF-TX-SMD

    DXLink™ Multi-Format Single Mode Fiber Transmitter, Duplex
  • DXF-TX-SMS

    DXF-TX-SMS

    DXLink™ Multi-Format Single Mode Fiber Transmitter, Simplex

Previous Versions